**SOLD** For Sale 69 Sardine Top Project - Complete or will sell parts seperately

G'day

due to us leaving the country I am going to have to let my 69 sardine top project go - just don't have the time to finish it

I have most parts - just need some rubbers and a wiring harness to finish it. Car was running and rego'd til last Jan, but stripped to replace floor pan. It's just about ready for the body to go back on now.

1500 motor, complete and was running fine - replaced heads
2 x 1500 heads - one good, one needs helicoiling
CB Performance drop spindles (not fitted)
Pan is rebuilt and painted, has new torsion bar rubbers, handbrake cables etc. I still have the original pan, which needs new pan halves - but may make rego easier as the chassis numbers will then be the same and the original engineers reports will be valid.
Honda prelude seats
Engineers report for the roof and seats conversion
steel 15" wheels running 205 on the back and 195 on the front

Body is OK - I've replaced a lot of metal around the heater channels and front inner wheel arches. there is still a bit of welding to do to get it finished - not pretty but solid!

Good doors, bonnet, guards, rear seats, bumpers etc etc

I'd rather sell it complete, as it's so near to being ready, but I'll break it if I have to.

complete car around the $750 mark or $1000 with the drop spindles

or

CB Performance Drop Spindles - $275 firm (that's what I paid for em!)
1500 heads - $50
Rolling pan - $400
1500 motor with all tinware and exhaust, carby etc - $450
Offers for the rest!

body is on trailer, so can deliver it locally, or pick up the lot on a car trailer!

cheers

Contact Info:

Terry
Northern Beaches, Sydney
0418 679217
terry@dtsband.com

[ Edited on 14-2-2006 by battybat ]

car when it was on the road!

car again

floorpan
new rear quarter on drivers side
rust on tunnel is surface rust from welding up bad chop to access clutch cable by a previous owner!
needs handbrake lever

pan and motor

CB Performance Drop Spindles

motor

also got:
carby kit
new bump stops
new valve stem seals
transaxle has new boots on it too

Keen on the motor and will be in sydney on friday arvo to have a look at it..
tom

Hey Tom

Friday is good - U2U'd you my address details

cheers

Terry

G'day

how much would you be wanting for the rolling pan minus box and motor?

pan wouldn't be rolling without the transaxle - do you have one already? - I'd rather let them go together - don't want to end up with a garage full of bits that end up at the scrap yard (though I probably will!)

make me an offer around the $300 mark!

cheers

Terry

[ Edited on 5-1-2006 by battybat ]

hey terry, just wondering if u seen me round. i drive a blue 1970 bug with whale tail.. and very noisy. i am on red p's. i also live northern beaches :P just havn't seen ur car round. :Pcheers, Matt.

hi Matt

car has been off the road for around 18 months now, so you wouldn't have seen it!

cheers

Terry

Spindles are for disc

postage to melbourne looks like about $15 - I'll included it in the price - so $275 all up - sent you U2U

cheers

Terry

Der Kafer Trieber - are you still interested in the rolling pan?

Hi,
Any pics of the seats? Have they been fitted to the rails or "as is" from the Honda?

Regards
Ctefeh

seats are fitted to the VW rails.

they need a damn good clean and a tidy up, but are yours for free if you want them

will take a pic later today

cheers
Terry

[ Edited on 9-1-2006 by battybat ]

[ Edited on 9-1-2006 by battybat ]

sorry mate, my internet has been on the fritz for a while, how much did you want for the rolling pan?

battybat, won't be able to get the pan only car i had for towing has now died!!!!

not interested anymore now

sorry mate

Is this still for sale? what is left?

yer, would those dropped spindles fit on a 1970 bug with disc brakes ? btw i am also on the northern beaches.

Hi All

Motor and Drop Spindles are sold

everything else is still available
floorpan (rolling)
doors
bonnet
deck lid
all guards
headlights
seats

Craig - you have U2U

All gone now - thanks guys!

Terry