Aussieveedubbers ยท General Chit Chat

Valla Last Minute

https://forums.aussieveedubbers.com/threads/98068/valla-last-minute

Smiley ยท

Who else is still working on their car getting it ready for Valla?

I was meant to clean my baja today but destroyed the internals of the steering box so I've spent the afternoon replacing that instead.

I'm leaving Thursday morning and I still need to replace my rear brakes, rear wheel bearings, and probably raise the rear suspension and notch the springplates too. Going to be some busy afternoons this week cause tomorrow I'm heading out offroading again, lets see if we can break something else ๐Ÿค˜๐Ÿค˜

Surely I'm not the only one doing this at the last minute, nothing motivates like a deadline!!!
So what are you all doing to your cars?

Will see you all at Valla!



Smiley ๐Ÿ™‚

69bug ยท

smiley what steering box are you using? i cant remember who it was but some one mentioned that they were having issues with a repro steering box?
ps i wish i was going to valla!!! good luck with your work ๐Ÿ˜ตโ€๐Ÿ’ซ

tar76 ยท

I hear you! Just fixed all my throttle linkage in side the cab on my bus today so hopefully evrything is good just got to start getting some spares together and i should be right to

Smiley ยท

69bug wrote:smiley what steering box are you using? i cant remember who it was but some one mentioned that they were having issues with a repro steering box?
ps i wish i was going to valla!!! good luck with your work ๐Ÿ˜ตโ€๐Ÿ’ซ
It was an original early style off a '61 Beetle. It broke because I had an altercation with a very big step in a rut, wasn't a repro box.

The one I've just put on is a very good condition orignal box out of a 1500 that I have here at home. Steering is smooth a silk with no play now.


Spares!! And packing? I'll probably be doing that Thursday morning before I leave!! ๐Ÿ˜‚๐Ÿ˜‚๐Ÿ˜‚


Smiley ๐Ÿ™‚

vwo60 ยท

I am still working on my ghia, a new 2275 with external oil cooler, thermostat, new interiour, complete the wiring , run the engine in and complete the first service before we leave

barls ยท

still need to clean, check and adjust the bug. plus pack and make sure i have enough beer. ill be there saturday peoples.

grumble ยท

barls wrote:still need to clean, check and adjust the bug. plus pack and make sure i have enough beer. ill be there saturday peoples.
you missed clean & polish!๐Ÿ™…

barls ยท

that falls under clean

11CAB ยท

Still working on the Baja. But the airlocker is in now ๐Ÿ™‚

h ยท

sitting drinking beer watching rock whiz thinking of doing something in the shed on my vw's for Valla..
does that count? ๐Ÿ˜

beetleboyjeff ยท

Just replaced the oil lines to my external cooler, adjusted the tappets, and gave it it's 630,000km oil change (not original engine).

Still have to drive to Inverell tomorrow night, clean a lot of bits & pieces on the car each afternoon during the week, then drive back to Port Macquarie on Friday night and probably clean bugs off it again, before meetin our local VWs at the Dennis Bridge (Hastings River) on Saturday morning and driving to Valla for the procession to Nambucca Heads.

Other than than just loaf around I reckon.

HappyDaze ยท

grumble wrote:
barls wrote:still need to clean, check and adjust the bug. plus pack and make sure i have enough beer. ill be there saturday peoples.
you missed clean & polish!๐Ÿ™…
That's what I'm doing......missing 'clean & polish'. Too many important things to do. [See below]. ๐Ÿ˜‚

Sides ยท

Heh heh - not much - just painting !!!

๐Ÿ˜€

rose ยท

Took mine for a drive yesterday to make sure the battery is charged and all is going good after the new clutch and clutch fork fitted the other week.

1303Steve ยท

Hi

Borrowing my mates car trailer to tow my sons bug up, he's racing at Raleigh, 3 people going up and his bug is a 2 seater so rather than take take 2 cars I thought it would be better tow it up.

I promised the owner of the trailer that I would repack the wheel bearing before leaving, it has electric brakes so I need to fit the brake controller I bought on eBay 18 months ago to my wife's Prado.

I need to give my sons bug a wash and set the valves.

Steve

DakDak67 ยท

Packed my Engle with beer..... oh how feckin nice ๐Ÿ˜€

toey1984 ยท

still building a removable roof for the manx, and leaving on Thrusday morning. eeep!.
hope its sunny and won't need it!

vvwbeetle ยท

Just a few things to check, if not sorted I'll leave have to leave the beetle at home and take an R32 golf instead.

Fitted new window reg a couple of weeks ago and fixed horn and hopefully have the lights sorted,

Only thing to fix now is my arm, not sure what has happened but it's swollen and can not bend my elbow or lift anything so hopefully a visit to the dr's will sort it.

Leaving Sydney Friday morning.can someone give me the details of the track,if we get there in time it would be nice to have a look.

matberry ยท

I'm putting in a new beam and spindles....I've already fitted a deep sump, changed oils and adjusted valves. ๐Ÿ™‚

h ยท

still sitting drinking beer watching telly
might look at my ride tomoro..
plenty of time ๐Ÿ˜€

VDU.88A ยท

Raleigh Race way has directions on the web site


http://www.raleighraceway.com.au/location.html

vvwbeetle ยท

Thanks

LIFE IN THE LOW LANE ยท

Fitting new front seats, trialling new wheels and tyres to see if they'll fit, grease front end, remove seats, fit bed and adjust steering box, sort electrical gremlin!!This is all on the to do list for Monday!

Sides ยท

Well yesterday was a beautiful day and managed to get the painting all done (4 guards, bonnet & deck lid).

So now all that's on the list is reassembly, some quick trailer mods, fluids check, tappets and change wheels & tyres... plus doing the usual 9-5 of course... may even squeeze in some time for a cut & polish !!!

๐Ÿ˜€

Calcool ยท

Hi,

I have been doing some work on the cabrio still not ready for rego but I will be trailering it down for the weekend on Friday and see if someone wants it more than me for the right money.

New King and Link Pins with drop spindles, 4 wheel drums now discs replaced or recod all brake lines. New Dual Cisruit Osize Mastercylinder, New HB Cables, Check all wiring and compelte 6 to 12V conversion, nearly ready.

Oh and fit Fuchs replicas and new tyres!

See you there,

Enjoy

David

h ยท

washed one vw this arvo.. getting there

Klaus ยท

perfection should never be rushed paully ๐Ÿ˜‚

kombibob ยท

Got the Oval regoed today but still a few things to do to it before Friday morn.

tar76 ยท

๐Ÿ˜  Alternator is tomoz job!

tin-bits ยท

All set now just need to pack over the next few days. Been up to Matt for a few final adjustments etc and can't wait I THINK!!!!!!!!!

Cheers Ian

LIFE IN THE LOW LANE ยท

Seats in, got rims on rear just have to get tyres for the front. Bed is in so just a quick wash on the outside and im almost ready to go...

h ยท

kombibob wrote:Got the Oval regoed today but still a few things to do to it before Friday morn.
good onya mate ๐Ÿ˜‰
you n ash will be fine ๐Ÿ‘

68AutoBug ยท

Smiley wrote:Who else is still working on their car getting it ready for Valla?

Surely I'm not the only one doing this at the last minute, nothing motivates like a deadline!!!
So what are you all doing to your cars?

Will see you all at Valla! Smiley ๐Ÿ™‚
Well I did a 50klm trip last night and when I got home found My temperature gauge wasn't working
[wire hanging under engine]
My speedo blinker light wasn't working
My oil pressure gauge wasn't working
probably loose wires..

a little bit of oil under engine.. small drip [no not Me]

I also need to raise the front off the shock rubbers..
and replace a tyre I wrecked last week when the air valve rubber split... and the tyre went down...
until it was only flat on the bottom.. still is.. lol

LEE

VDUBXTC ยท

68AutoBug wrote:
Smiley wrote:Who else is still working on their car getting it ready for Valla?

Surely I'm not the only one doing this at the last minute, nothing motivates like a deadline!!!
So what are you all doing to your cars?

Will see you all at Valla! Smiley ๐Ÿ™‚
Well I did a 50klm trip last night and when I got home found My temperature gauge wasn't working
[wire hanging under engine]
My speedo blinker light wasn't working
My oil pressure gauge wasn't working
probably loose wires..

a little bit of oil under engine.. small drip [no not Me]

I also need to raise the front off the shock rubbers..
and replace a tyre I wrecked last week when the air valve rubber split... and the tyre went down...
until it was only flat on the bottom.. still is.. lol

LEE
What? Your wiring isn't up to scratch Lee? that really suprises me. ๐Ÿ˜‚
Hope you get your tyre sorted and ill see you there.

ian.mezz ยท

68AutoBug wrote:
Smiley wrote:Who else is still working on their car getting it ready for Valla?

Surely I'm not the only one doing this at the last minute, nothing motivates like a deadline!!!
So what are you all doing to your cars?

Will see you all at Valla! Smiley ๐Ÿ™‚
Well I did a 50klm trip last night and when I got home found My temperature gauge wasn't working
[wire hanging under engine]
My speedo blinker light wasn't working
My oil pressure gauge wasn't working
probably loose wires..

a little bit of oil under engine.. small drip [no not Me]

I also need to raise the front off the shock rubbers..
and replace a tyre I wrecked last week when the air valve rubber split... and the tyre went down...
until it was only flat on the bottom.. still is.. lol

LEE
I would try cleaning some of the paint from off of the wire connectors ,๐Ÿ˜‚๐Ÿคช๐Ÿ˜‚

68AutoBug ยท

Sides wrote:Well yesterday was a beautiful day and managed to get the painting all done (4 guards, bonnet & deck lid).

So now all that's on the list is reassembly, some quick trailer mods, fluids check, tappets and change wheels & tyres... plus doing the usual 9-5 of course... may even squeeze in some time for a cut & polish !!!

๐Ÿ˜€

You mean to say You are working too Dave....???

YIKES

LEE

vvwbeetle ยท

Took the car for a run this morning thinking everything was sorted, I stopped got out to check it out and saw all my new engine oil pouring out.now have to get a new cooler fitted to engine and hope that sorts it and have it done in time to leave Friday morning.

h ยท

washed two more today..
now decisions decisions as to what to take...?
starting to panic as hopefully all the swap meat stuff will fit in
oh dear ๐Ÿ˜ต

tar76 ยท

Thankfully the alternator wasn't the problem, just a stuffed regulator so worked out to be a lot cheaper. Now it's time to hit the road Thursday morn bring it on!!!

donn ยท

Did a wheel cylinder on the rear brakes driving into the garage this morning, Better now than half wayto Valla, no fluid on the road where I had it parked or on the drive, didn't notice the leak till 3.00pm, fluid started about a metre into the garage, have replaced cylinder and shoes, starting on the other side (why not?) then waiting till tomorrow for a hand to bleed em. Thank you Mr. Nymeyer.

h ยท

lucky man mr donn

1303Steve ยท

Hi

Replaced the wheel bearings on the car trailer and fitted the electric brake controller.

Just need to adjust the valves on the bug and give it wash and then pack.

Steve

Smiley ยท

I just spent the afternoon on the Baja.

Replaced the engine and transaxles oils.
Adjusted rear brakes.
Cleaned and reoiled air filter.
Replaced faulty oil pressure warning light sender.
Greased the front end.
Fitted a new blue plate.

I gave the engine a quick degrease.

Still have to clean the poor thing and fit new handbrake cables tomorrow before heading off Thursday.

As well as pack, I better do that too lol.



Smiley ๐Ÿ™‚

polarbus93 ยท

ok ive changed the oil and plugs replaced the leads and had it running sweet all day then drove out tonight and well its running very rough tonight ,so now have to figure it out and hook trailer up and pack clothes food and drinks before thursday morning

tar76 ยท

Might have to write my AVD name on our shirt's so i can put some faces to names.

beetleboyjeff ยท

At the nationals and bugs & busses by the bay, I put mine on an old name tag I had - met heaps more people because they knew who I was for a change. :-)

I plan to do the same at Valla.

Smiley ยท

tar76 wrote:Might have to write my AVD name on our shirt's so i can put some faces to names.
I'll be there, just look for the guy in the VW shirt ๐Ÿ˜‚๐Ÿ˜‚



Smiley ๐Ÿ™‚

tar76 ยท

I might just cut a bit of duct tape and write my avd name on it. Make sure if you notice my name say hello

polarbus93 ยท


bit of art before we go in the morning see you all up there if the van makes its

Smiley ยท

Who else is still working on their car?

I just rebuilt the pedal assemble on mine and gave the inside a quick vacuum. Still need to wash her and pack for tomorrow and I'm running out of daylight!!!

I hope that everyone else has their cars sorted!



Smiley ๐Ÿ™‚

polarbus93 ยท

i couldnt work out why my fuel gauge isnt working after two weeks and i hope ive solved my flasher problem and need to sort food and drinks out and load them and clothes into van

tar76 ยท

I'm done just sleep and turn the key tomorrow morn 5am. Hoping to meet some crew at Yatla BP on the way.

h ยท

had a crisis this afternoon
just finished with the VW for Valla and then noticed... shock horror
that I was on my last beer in the fridge.. ๐Ÿ™
things were going along way to smoothly.. ๐Ÿค“

yatala BP what time u there tar?
I'm outta here about 4.30am so I can miss the crapola traffic ๐Ÿ˜€

tar76 ยท

h wrote:had a crisis this afternoon
just finished with the VW for Valla and then noticed... shock horror
that I was on my last beer in the fridge.. ๐Ÿ™
things were going along way to smoothly.. ๐Ÿค“

yatala BP what time u there tar?
I'm outta here about 4.30am so I can miss the crapola traffic ๐Ÿ˜€
Mate 7am meeting there. I''ll probably be just over half hr in front of you man.

Sides ยท

Skyved off work for the arvo to get Jezzi finished, so all good and and have just loaded her onto the trailer... not really a Valla unless cutting it fine I reckon...

Now all that's left is to sort out food and booze, pack some warm clothes and make sure have all the racing necessities and am good to go.

๐Ÿ‘

h ยท

tar76 wrote:
h wrote:had a crisis this afternoon
just finished with the VW for Valla and then noticed... shock horror
that I was on my last beer in the fridge.. ๐Ÿ™
things were going along way to smoothly.. ๐Ÿค“

yatala BP what time u there tar?
I'm outta here about 4.30am so I can miss the crapola traffic ๐Ÿ˜€
Mate 7am meeting there. I''ll probably be just over half hr in front of you man.
I'll be there about that time in the T5 rocket ship..
it'll be the first time in a while i use the heater I reckon ๐Ÿคช
c u there.. pauly

Woops more like after 6 but traffic will impede the need for speed
travel safe all

tar76 ยท

Ok

Smiley ยท

Just finished packing.

About to leave and start my 2700+ km roadtrip!

Everyone please take it easy on the road.

I'll see you all this weekend!



Smiley ๐Ÿ™‚

tar76 ยท

good luck and safe journey mate.

toey1984 ยท

Finished roof on buggy at 12.30 last night and new oil cooler mount ( this time fixed to car rather than hanging on the road like last one???)
Bus packed and ready to go.
splash of 98ron and lets go at 8:30am.
Safe trip peoples who are traveling long km