rattle can spray job
stoppa - January 13th, 2012 at 11:50 AM
i got bored over xmas so repainted the rod, read about it in old skool rodz mag lay down some red oxide then satin black rub back with 1500 and hand
poilsh looks like 100 year old lacqer.i managed to find a ragtop out of a mazda121 fit the roof just nice changed it from 3 fold to a 2 fold sewed up
a new cover looks cool i think. the second and 3rd last pic is with old top
hellbugged - January 13th, 2012 at 01:04 PM
Looks the goods......needs red on the wheels now IMO
Been my fav Aussie rod since ya first started building it
Doug Sweetman - January 13th, 2012 at 04:38 PM
Hey stoppa, top looking rod mate !!!
Is it rego'd in WA like the plates say ? If you did rego it here, do you mind if I ask how you went getting it approved with the chop top, suicides
and bicycle guards ? Also, how much of an engine cover did they make you put on it ?
Really clean looking beast, well put together !
stoppa - January 13th, 2012 at 06:38 PM
look its not hard to rego a volksrod in any state in aus
roofchop ok cut and extend pan ok tyers must have cycle gaurds and vehicle must be pre 1972 engineer i used was dan pitic he is in hillarys one
more thing to do it here u have to fill out the paper work and send to the technicle section in weshpool
Doug Sweetman - January 13th, 2012 at 09:59 PM
That's cool to hear, I thought it was harder than all that...
ran5 - February 1st, 2012 at 02:48 PM
| Quote: |
Originally
posted by stoppa
look its not hard to rego a volksrod in any state in aus
roofchop ok cut and extend pan ok tyers must have cycle gaurds and vehicle must be pre 1972 engineer i used was dan pitic he is in hillarys one
more thing to do it here u have to fill out the paper work and send to the technicle section in weshpool
|
mate, can u expand on this, only as maybe the info i am getting is up shit creek. I have been told following, beam extension needs to be made by
certified welder, ie can sign off on it, has full tickets etc, that needs to then be xrayed, technically then you can have issues as its extended, and
they need to test car rigidity etc....rear, well i have drop plates and engine tranny lift, so that needs engineering also. Roof chop most comply also
to visibility test. as car is now modded you need retractable seat belts to meet rod rego guidlines. I have bomber seats, these too need full
covering, list kinda goes on. If you are willing can you share some info, as maybe im getting incorrect advice, and this is just for club rego, not
full, ive been told forget about full rego in vic on a volksrod....please see in other thread i was under impression that no legal cars existed, but
that was cleared up by some of the other guys here. cheers
stoppa - February 2nd, 2012 at 08:40 PM
| Quote: |
Originally
posted by ran5
| Quote: | Originally
posted by stoppa
look its not hard to rego a volksrod in any state in aus
roofchop ok cut and extend pan ok tyers must have cycle gaurds and vehicle must be pre 1972 engineer i used was dan pitic he is in hillarys one
more thing to do it here u have to fill out the paper work and send to the technicle section in weshpool
|
mate, can u expand on this, only as maybe the info i am getting is up shit creek. I have been told following, beam extension needs to be made by
certified welder, ie can sign off on it, has full tickets etc, that needs to then be xrayed, technically then you can have issues as its extended, and
they need to test car rigidity etc....rear, well i have drop plates and engine tranny lift, so that needs engineering also. Roof chop most comply also
to visibility test. as car is now modded you need retractable seat belts to meet rod rego guidlines. I have bomber seats, these too need full
covering, list kinda goes on. If you are willing can you share some info, as maybe im getting incorrect advice, and this is just for club rego, not
full, ive been told forget about full rego in vic on a volksrod....please see in other thread i was under impression that no legal cars existed, but
that was cleared up by some of the other guys here. cheers
|
i dont know if i can help much ,here in perth we cant go under the guide lines of street rod rgo fullstop
i first had the car engineered in nsw easy, went to an egineer told him what i wanted to build, this what he said
car must be pre 1972 to allow the following
roofchop ok
remove gaurds replace with cycle gaurds ok
suicide doors ok
bolt on beam ext a big no/cut and extend thats fine
the same here in perth car was re engineered here by dan pitic
as far as i was told by engineer in nsw was that what i did to my car i could get it regersted in any stae in aus.
look a bolt on ext will set u back aprox $300 bucks landed then the drama and expense of finding a engineer to aprove it and then maybe pay for xray
.
my beam ext cost $30 bucks in metal one free panhead and one day cut and weld less than 6 hours work
i wish u all the best and hope u get it on the road, keep up the good work{,volksrods the peoples rod}. Brock
5lam - February 14th, 2012 at 08:49 AM
Did you use the whole roof clip out of the 121 or just the sunroof and rails?
stoppa - February 21st, 2012 at 08:21 PM
just the sun roof it just unbolts from the 121 roof
5lam - February 22nd, 2012 at 08:10 AM
Thats a great idea! I've been looking for a ragtop for a while, but never thought to use something else.
Can't imagine it being easier to find than a Beetle one though.