Is this the one that was for sale not-so-long ago?
-Staggers.

Ouch, that's harsh.
-Staggers.

I am after a rear corner, tow bar, bumpers.
really need the rear corner. Will pay you for your troubles

yep i was trying to sell it as a running beast, now pulling bits off, motor and gearbox , susp, brakes rear/front bumpers now gone... only really body/doors/glass/electricals and some funky looking camper interior left.. stove sink etc in a nice timber setup.. thanks for the calls people

im after both window washer jets, and door slider bit (below). Will you ship to syd?

dude, no worries ill ship anything to anyone, the door slider works great.. ill pull them off awaiting your details... tim

How are the front rubber mats that sit on top of the wheel arches?
Would these fit a 75 Kombi? I'm in need of the passenger side piece as mine is ripped where careless passengers have cought it with their feet
If you need a pic of what i'm after just let me know.


[ Edited on 26-4-2006 by hallph ]

Is the floorpan still in 1 piece? Or a victim of rust? After p/s section about 400mm wide from the step. I think the quarters that you can buy new wont quite cover it...
shano

don't suppose you want to cut panels off for cash will you?

ill cut it beerboy what you after, shano floorpan is pretty sad, esp front.. hallph ill have a look at them tomorrow.. but i think i remember some of the matt tornish

big jobs mate. hole rear corner drivers side from roof to floor and the long straight panel with the fuel flap.

Will give cash and come and help if you like. thanks

Still got the steering box?
Indicator assembly?
Rob

sorry frenzix, never mind about the door slider... have sourced a new nylon block for it which is what i was after.

Frenzix,

Does this van have the seat mounting plates for the middle seat as in a Microbus?

If Yes - are they in any sort of decent condition?

Mine are rusted, mainly the underneath bit that seals the van floor?

Happy to pay for time and effort if in good nick

Josh

beerboy rear corners are rusted out badly but above the battery tray area is good to roof, long straight panel still there take photo of where you want me to cut,, steering box still there, indicator assembly gone as of yesturday, jb4845 there id timber screwed to the floor ill take it off soon and checkout the plates.. tim

hallph the rubber is torn up sorry

I'm looking for front right vent window and frame thats not rusted out.

I need early model drivers side internal door opener. Petrol Guage/Speedo and early bay ignition. I have attached photos of the type I,m after.

Thanks,

Bill

Tim.. If you can get the steering box ready and U2U me postage costs and your bank details.. Thanks Mate..
Rob

doesnt have a bullbar that can mount on a 76 does it, perchance?

a long shot..but hey!

buttercup sorry no,

stenguns ill pull the steering box tomorrow..

72 twincab send me your details as i have already pulled them out do you need the plastic scratch plate? i have the opener out too. .. ready to rock and roll.

duddreamer the vent window is el crappo in this..

beerboy im half cut through the bits you want,

lobus i have your bits ready.. no key though sorry..

tim

just to prove ive started the work

[ Edited on 29-4-06 by frenzix ]

76camper, washer jets are out and pulling slider off tomorrow

beerboy, bumpers are taken


i have all glass out, engine lid, headlights, right front indicator bezel.. all pulled still more to go

started the tip pile in the ute

[ Edited on 29-4-06 by frenzix ]

How is the front right corner around the indicator?

ummmm i think its ok, ill take a peek tomorrow... how much around the indicator? can you mark it out for me in a piccy? .. tim

About here would be good if possible....

Really need the bottom edge of the pressed section near the light down to a bit below the roll under the indicator right out to the corner.

The more meat around the graft the better.

If it can be cut and is good let me know how much and the account to credit.

Cheers, Matt

[ Edited on 29-4-2006 by HotRodMatt ]

Thanks Tim I will see Monday. I forgot to ask you what do I owe for the bits?

i only accept beer for payment, the amount is your choice

hey matt, just had a look it should be fine to cut... ill do it tomorrow..

Tim

but really i only want the shipping charges payed for. i'd rather see people use bits from this one than scrap it totally.