Aussieveedubbers - Powered by GaiaBB

WTB Master Cylinder Push Rod.

Pumba - June 22nd, 2012 at 07:35 PM

Im looking for a brake master cylinder push rod to fit a 56 oval.
Contact By PM.
Cheers Shane.

Pumba - June 25th, 2012 at 07:50 AM

bump

vw54 - June 25th, 2012 at 09:26 AM

you will need 2 hand brake cables

Better off doing both at once as if only 1 done then it strains the other and it will break

Pumba - June 25th, 2012 at 11:03 AM

Handbrake cable i can buy new,i really need the pushrod and clevis i think they call it.

Special Air Service - June 25th, 2012 at 01:26 PM

got a picture of what they look like Shane?

Pumba - June 25th, 2012 at 11:27 PM

Quote:

Originally posted by Special Air Service
got a picture of what they look like Shane?

No picture sorry,it has to be from a roller pedal set up,its a rectangle bloke with the rod out the end of it ???

Newt - June 26th, 2012 at 12:02 AM

Anything like this. This is from a '59.

Newt - June 26th, 2012 at 12:05 AM

If it is part 20 that you are needing, cut the end off a bolt and taper / round the end.

Newt

Newt - June 26th, 2012 at 12:09 AM

Second thoughts, I recant my above suggestion.

Newt

Pumba - June 26th, 2012 at 08:52 AM

Thanks newt parts 20 and 21 are what i need.
cheers shane.

Pumba - June 29th, 2012 at 09:12 AM

Still looking.

Birdman - June 29th, 2012 at 06:46 PM

I'll have one in the shed shane but i'm not back in sydney till the 7th.

Pumba - June 29th, 2012 at 07:32 PM

Quote:

Originally posted by Birdman
I'll have one in the shed shane but i'm not back in sydney till the 7th.

PM sent.

Pumba - July 7th, 2012 at 05:33 PM

Ron another PM sent.

Birdman - July 7th, 2012 at 07:53 PM

Going shed diving tomorrow mate.

Birdman - July 9th, 2012 at 12:01 AM

No good on the pushrod Shane but you can have that ribbed guard for $50. its a rear right.

Pumba - July 10th, 2012 at 07:57 PM

Still looking ???

volumex - July 10th, 2012 at 09:34 PM

Like this?:

http://www.wolfsburgwest.com/cart/DetailsList.cfm?ID=113721205A

I need one too, managed to snap an arm off when I removed it - it did require a bit of tender loving force.

Pumba - July 11th, 2012 at 06:36 AM

Quote:

Originally posted by volumex
Like this?:

http://www.wolfsburgwest.com/img/wwpn/113721205A.jpg

http://www.wolfsburgwest.com/cart/DetailsList.cfm?ID=113721205A

I need one too, managed to snap an arm off when I removed it - it did require a bit of tender loving force.

Yep and i need the rod.

HappyDaze - July 11th, 2012 at 08:06 AM

Quote:

Originally posted by volumex
Like this?:

http://www.wolfsburgwest.com/cart/DetailsList.cfm?ID=113721205A

I need one too, managed to snap an arm off when I removed it - it did require a bit of tender loving force.

Hope you're OK.....although they can do wonders these day with micro-surgery.

Pumba - July 23rd, 2012 at 06:43 AM

Bump

bushed - July 23rd, 2012 at 10:21 PM

make one from sqr tube steel insert nut and attach a rounded off bolt
cut other end and drill
as per part pic
i will look what I have now the rain has stopped.

Pumba - July 24th, 2012 at 06:35 AM

Hi bernie,let me know if you have one,id rather the original than make one.

bushed - July 25th, 2012 at 03:40 PM

no luck yet but I will look in my Mercedes stasch now

Quote:

Originally posted by Pumba
Hi bernie,let me know if you have one,id rather the original than make one.

Pumba - July 25th, 2012 at 04:47 PM

No worrys,one will turn up.

Aussie - July 25th, 2012 at 08:14 PM

Quote:

Originally posted by Pumba
No worrys,one will turn up.

I bought a used rod for mine from Vintage Vee dub. Cost me $5. Give them a call.

Pumba - July 25th, 2012 at 08:22 PM

Quote:

Originally posted by Aussie

Quote:

Originally posted by Pumba
No worrys,one will turn up.

I bought a used rod for mine from Vintage Vee dub. Cost me $5. Give them a call.

I asked boris the other week when i was there but he has none.

Pumba - July 29th, 2012 at 08:23 PM

Getting desperate now,i need to get my brakes working.

HappyDaze - July 29th, 2012 at 09:27 PM

How much time have you spent on here, looking for the push-rod, Shane?.....and how long would it take to make one? :smilegrin:

grumble - July 29th, 2012 at 09:36 PM

Shane did you get a pushrod,I saw the early posts and assumed that you had it under control.I am fairly sure there is one on a cluster in the shed,I will check tomorrow. PM if still searching. I could take it to Valla if it is there. Les