| [ Total Views: 731 | Total Replies: 14 | Thread Id: 101393 ] |
|
|
 vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2013 at 11:12 PM |
|
|
In a bit of trouble with Avis Adjusters - help please!
Hi folks,
A little help please to get me back on the road in time for Das Resto Haus open day on Sunday!
I've attempted to lower my bug a little this evening and I've not had the outcome I was expecting. I have a beam with Avis Adjusters and here's
what I thought the process would be:
1. raise the car, support on bricks or similar, and settle suspension
2. raise the car slightly so trolley jack to takes the weight
3. loosen the avis adjuster bolts
4. slowly lowerer the car to desired position
5. tighten avis adjuster bolts
However, when I loosened the bolts in step 3 the bolt snapped to the bottom position as shown on the photo. I expected the bolt to adjust up or down
with the height of the trolley jack but it's firmly snapped into this position. The plates and teeth are perfectly loose. If I drop the jack the car
will go super low but as mentioned the avis adjuster bolt does not move.
Thanks for your advice
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2013 at 11:16 PM |
|
|
another shot if it helps
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on March 29th, 2013 at 05:52 AM |
|
|
Lifting the car will move the adjuster to the highest position.....and, actually, getting the adjuster up higher will raise the car.
You need to make sure that the two tubes/torsions are not fighting against each other,
so both will need to be backed off.
While there is any tyre contact, the adjuster will stay put,
so you may have to raise the tyres clear off the ground.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2013 at 07:54 AM |
|
|
thanks for the reply. both bolts are eased right off but are not moving regardless of if I raise or lower the car - so you are saying this is because
the tyres are on the ground? But how can I raise or lower the suspension without having contact with the wheels? thanks
|
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on March 29th, 2013 at 08:13 AM |
|
|
The grub screw should stay in during the process....use an allen key to hold it and take those nuts off out of the way so you can remove the plate.
i think your technique is sound with the car and jack. If all is loosened off so the teeth release on the plates and the car lifted off the ground,
the adjuster should go to it's highest point.
Pictured you have it at it's lowest, until you get the treads off the ground again with the nuts and plates off, it will stay there.
|
|
|
vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2013 at 08:27 AM |
|
|
Thanks hellbugged, the grub screw snapped to the position shown in the photo when I loosened the bolts - I'm wondering if the grub screw was
unscrewing with the bolts - I wasnt using an allen key to hold it in place. Am I right in saying theres a dimple in the torsion leaves which the grub
screw should be in, but may now be out? And if so this sounds like a major problem.
|
|
|
Special Air Service
Custom Title Time!
Chief "Gunna"
Posts: 1769
Threads: 210
Registered: October 4th, 2004
Member Is Offline
Location: Old Bar , Mid North Coast , NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: In desperate need of a decent sleep
|
| posted on March 29th, 2013 at 09:29 AM |
|
|
looks like you are at the bottom limit of your adjusters to me?
[size=5] Calling all NSW Mid North Coast Veedubbers
Click Below [/size]
[size=6]Mid North
Coast VW [/size] |
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on March 29th, 2013 at 11:46 AM |
|
|
Your forgetting the bars are supporting the vehicle, so they always twist under weight. You need to jack the car up further and by adjusting the
vehicle ht. you will see the adjuster move, but it needs to be higher. There are a few variations as mentioned above, whether both adjusters are set
to a similar angle so they share the load equally, also if narrowed the bars get a little stiffer so don't twist as much, but essentially the bars
always twist the same amount from the load of the car, you are moving the bars anchoing point.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2013 at 02:34 PM |
|
|
mission complete, thanks eveyone for your advise. one last question tho, ditch the roll bar for extra clearance or go an inch higher and keep it?
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on March 29th, 2013 at 03:13 PM |
|
|
Roll bar??
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
vorsprungdurchtechnique
Commited Dubber
Posts: 67
Threads: 21
Registered: August 10th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2013 at 03:55 PM |
|
|
sway bar, you no what I think i've answered my own question, it's staying on! cheers
|
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on March 29th, 2013 at 05:04 PM |
|
|
That's a f'n nice ride!
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on March 29th, 2013 at 05:59 PM |
|
|
needs to go lower
|
|
|
newghia
A.k.a.: Noddy
Wolfsburg Wizard
stock is for people who cant think outside the square
Posts: 679
Threads: 30
Registered: May 29th, 2008
Member Is Offline
Location: western sydney
Theme: UltimaBB Pro Charcoal
Mood: nood !
|
| posted on March 29th, 2013 at 07:19 PM |
|
|
Only at the back !!!!!
C'mon, you've got ALL day tomorrow to sort that out ! 
Step up to get out !!!
|
|
|
beetle_nut
Wolfsburg Wizard
Posts: 465
Threads: 55
Registered: January 22nd, 2012
Member Is Offline
Location: brisbane
Theme: UltimaBB Pro Blue
Mood: rollin low n rollin slow.65 notch back and 59 beetle
|
| posted on March 29th, 2013 at 08:10 PM |
|
|
Nice bug..
Lower in the back would look good..
|
|
|
