| [ Total Views: 745 | Total Replies: 17 | Thread Id: 103515 ] |
|
|
 tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 20th, 2013 at 04:46 PM |
|
|
Type 3 rear wheel bearings
About 10 weeks ago my engineer replaced a rear wheel bearing. Torqued it up to the specs from memory over 200 lbs even near 300. whatever it was.
The swing arm is Panther custom one. I had a new axle on hand as well as the new bearings. Today I had my Cv boot repalced and my mechanic inforemd
me that there is slop in the wheels bearing. couple of mm's.
Why would this occur? Whenever I've had one replace dits lasted 10 years or more. What would cause this?
Thanks
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on September 20th, 2013 at 08:51 PM |
|
|
The wheel bearing could have been a cheap and nasty one or it was installed incorrectly and damaged during the process, what is the layout of the
trailing and what is the bearing configuration, does it use a cartridge bearing , what was the brand of the bearing .
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on September 20th, 2013 at 10:50 PM |
|
|
| Quote: | Originally
posted by tweety
About 10 weeks ago my engineer replaced a rear wheel bearing. Torqued it up to the specs from memory over 200 lbs even near 300. whatever it was.
The swing arm is Panther custom one. I had a new axle on hand as well as the new bearings. Today I had my Cv boot repalced and my mechanic inforemd
me that there is slop in the wheels bearing. couple of mm's.
Why would this occur? Whenever I've had one replace dits lasted 10 years or more. What would cause this?
Thanks
|
If its an IRS rear end similar to a beetles, there is a spacer between the bearings, which causes the problem of play over time... [slop] from what I
have read..
a mechanic who did My rego check a couple of years ago mentioned it.. naturally it wasn't a couple of mms.... even if measured at the top of the
tyres..
Ask your Mechanic if He uses Lithium based Moly grease -[ a Blackish grease] as per VW manuals.. or the green clay based grease which I wouldn't use
on a push bike.. ? The lithium based Moly grease WILL make CV Joints and bearings last a very long time... but they need to be packed fully too..
which is quite messy with lithium based grease..
apart from that, the most important thing is the brand of the bearings... also if the correct high load bearing is used, as many people just use two
cheap ball bearings as they are much much cheaper than the expensive roller bearing used on the outside..
also the inner ball bearing which [like a 6206C3 or 6306C3] should have no seals on it as there is only a very small amount of green grease inside
those.. and filled with lithium based MOLY grease.. it also needs to be a C3 bearing.. The original outer bearing is expensive like an NU206 or NU306
and also needs to be well packed with lithium grease.. The rear axle nut torque is 217 ft lbs..
Now how You are going to find any of this information out..
I don't know....
I know that I have cleaned and refilled My original Bearings and CV Joints with Lithium based Moly grease back about 2003 in My 68 semi auto Beetle
that has the CV Joint rear end... I also know they will last for a very long time due to the lubrication...
I can only suggest You ask for the 2 old bearings He is going to replace to check what bearings were used and what grease was used.. CV joint boots
usually show surface cracks long before they actually rip apart.. I replaced two of mine when they first showed signs of cracking...
Best of Luck
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on September 20th, 2013 at 11:04 PM |
|
|
Hi
If your trailing arms are anything like VW ones they can flog out which will give you slop in the vertical, you can also get oversize circlips to
remove in & out movement.
Steve
|
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 21st, 2013 at 09:12 AM |
|
|
Thanks guys. I do know that a very good engineer/mechanic did the other side LHS a few mobnths ago. We got a bearing kit supplied by Panther trikes.
The kit included a new axle, two bearings and two journals. The journals were crap in that they were undersize. He made up two new ones on a
lathe.
So I had a second kit ready to do the other side RHS- the side that has slop in it now. But at that time (June 2013) there was no slop and no problem
detected. So we left it.
4 weeks later I'm getting the trike frame strengthened at another engineering place and they said the wheel bearing RHS had slop in it. So then I
supplied the kit. They only used the bearings and the journals in that kit, didnt use the new axle.
Which poses a few question. Firsltly I suspect they didnt realise like the first engineer (who seemed real thorough) that the journals were too
small. I think I'll have to return to the first engineer to get it done correctly.
I dont know the bearing make or details. The swing arms are alloy custom box section Panther trikes exclusive.
Thanks fellas for your replies.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on September 21st, 2013 at 10:31 AM |
|
|
It is very hard to comment if we cannot see the type of bearing configuration, when you talk about journals and as a machinist I think about bushes
not ball or roller bearings, as to the fact they were machined seams strange, any photos of your set up.
|
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 22nd, 2013 at 08:16 PM |
|
|
No pics yet VW060. But the guy that did the bearings a few weeks ago in that wheel has offered to pull it all apart again and fix it. good. I have a
new axle too. in 2-3 weeks he will get the trike and I'll be there to watch. will take pics then too. regards. Tony
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on September 22nd, 2013 at 08:37 PM |
|
|
check to see if the bearing housing has a 311 part number
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on September 23rd, 2013 at 08:33 PM |
|
|
Does it have type three rear wheel bearings?.
|
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 8th, 2013 at 06:01 PM |
|
|
it is modelled on type 3 axles. Panther however make their own swing arms from alloy box section.
Here is a kit I have from Panther ready if required by the engineer next week. The bearings are roller type Nachi 6206C3 and NU206EG C3. same as you
advised 68autobug. 
Interesting about the thicker circlip. anyway will be present when he dismantles it all. and will emntion the moly lithium grease. might be a
greasy version of the pills I used to swallow. lol
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on October 9th, 2013 at 10:52 AM |
|
|
The bit that holds the bearing into the axle housing what part number does it have?? 111 or 113 is beetle 311 is type 3 the housing are very slightly
different and cause the issue u are experiencing.
"If at first you don't succeed, skydiving is not for you." - Anonymous |
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on October 9th, 2013 at 12:02 PM |
|
|
Use good quality wheel bearing grease......NOT moly. Moly tends to cause the balls to 'skid', rather than roll [nothing worse].
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2013 at 08:43 PM |
|
|
thanks guys. will be getting it done tomorrow - Friday. will rpint this out and use it.
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on October 10th, 2013 at 09:10 PM |
|
|
| Quote: | Originally
posted by empi
The bit that holds the bearing into the axle housing what part number does it have?? 111 or 113 is beetle 311 is type 3 the housing are very slightly
different and cause the issue u are experiencing.
|
those gaskets as well.
Type 3 don't have them and that would cause the retainer to not retain the bearing properly and that even if its a IRS retainer for type 3 as Empi
says ^
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on October 10th, 2013 at 10:19 PM |
|
|
| Quote: | Originally
posted by HappyDaze
Use good quality wheel bearing grease......NOT moly. Moly tends to cause the balls to 'skid', rather than roll [nothing worse].
|
too right, moly is only for slow moving bearing or bushes. like suspension bushes, U joints and CVs etc...
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 11th, 2013 at 03:51 PM |
|
|
took tweety trike to the engineers. engineer took it apart. when he began he noticed the axle nut loose. the bearings were cool to touch even after
50kms. We had those spare bearings, seals and avle but after an assessment they werent needed. Torqued them up to 220lbs and no slop at all.
Maybe they settled in? All I know is it was nice to ride without the slop.
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on October 13th, 2013 at 09:44 AM |
|
|
220 they can still come loose. A lot of the guys here do them up to 300 ft-lb
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 13th, 2013 at 02:36 PM |
|
|
yeh, will take a note of that. and he did use wheel bearing grease. thanks for your replies guys.
|
|
|
