| [ Total Views: 559 | Total Replies: 5 | Thread Id: 104292 ] |
|
|
 Laverda Bomber
Casual Dubber
Posts: 43
Threads: 15
Registered: September 23rd, 2009
Member Is Offline
Location: Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 4th, 2013 at 05:18 PM |
|
|
Oil Gallery Plug
My 77 camper 2 litre spat out a little plug behing the flywheel and dumped all its oil.
Anyone come accross this before?
Normal remedy?
Any advice welcome.
Bottom lhs of photo shows the culprit.
Regards
Bomber
[img] [/img]
|
|
|
cb john
Wolfsburg Wizard
Posts: 470
Threads: 6
Registered: June 22nd, 2007
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue
|
| posted on December 4th, 2013 at 06:00 PM |
|
|
Remove it, tap and use screw in plug...
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 4th, 2013 at 06:57 PM |
|
|
That one is very difficult to repair, just behind where the plug was is the fuel pump pushrod location. The pushrod runs in a brass sleeve thats
pressed into the case, you can see it blocking 1/2 the hole. So to repair you can only work in the alloy before the guide. if you put a hole into the
tube the only way to fix it is to split the case which can turn into a rebuild.....
The other problem is any shavings that get in go directly to the lifters on that side.
Good luck
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Laverda Bomber
Casual Dubber
Posts: 43
Threads: 15
Registered: September 23rd, 2009
Member Is Offline
Location: Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 5th, 2013 at 07:09 AM |
|
|
Intending to split the cases anyway.
Is the brass sleeve simple to remove and replace to allow me to tap and plug the offending hole?
Cheers
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 5th, 2013 at 07:21 AM |
|
|
I have cut down a 3/8 npt tap so you can start it in a shallow hole, i just removed the lead, works perfectly. just a bit harder to start.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 5th, 2013 at 10:56 AM |
|
|
| Quote: | Originally
posted by Laverda Bomber
Intending to split the cases anyway.
Is the brass sleeve simple to remove and replace to allow me to tap and plug the offending hole?
Cheers
|
Yes, but a proper drift machined to suit to give some protection to it dimensions is strongly recommended. As Shayne suggested is
probable better unless your deleting the mechanical pump. It does get involved as to plugging the correct gallery if removing the guide tube
permanently.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
