| [ Total Views: 576 | Total Replies: 4 | Thread Id: 104439 ] |
|
|
 tin-bits
Casual Dubber
Posts: 45
Threads: 14
Registered: September 23rd, 2009
Member Is Offline
Location: Morayfield Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 19th, 2013 at 06:39 PM |
|
|
2 ltr type 4 rebuild for the gurus.
I am rebuilding a 2ltr type 4 engine and have a problem that I have no answer for.
Area is crankshaft assembly.
Problem is.
Timing gear on the crank has 28 teeth and is approx 76mm OD but has no position indicator marks to line up the cam gear.
My solution was get a new gear and work out the position off the new gear and all should be good.
Wrong,,,,,
The new gear only has 25 teeth and only 70mm OD.
What the.
Obviously the 70mm gear will not mesh with the cam gear as it is too small in dia.
Anyone any ideas or had this problem?
HELP before I go nuts.
Cheers Ian
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on December 19th, 2013 at 08:31 PM |
|
|
The new gear is for a type 1 motor, not a type 4.....so that's your problem !
Place your type 4 gear on a table with the chamfer side facing down. Position the key way slot in the 12 oclock position. At the 6 o'clock position
(opposite the keyway in a straight line) you will see a valley in the gears (bottom of the tooth).....now move one valley over to the left (towards 7
oclock) and that is where the dot on the cam should be placed.
send me your email and I can send you a pic.
|
|
|
tin-bits
Casual Dubber
Posts: 45
Threads: 14
Registered: September 23rd, 2009
Member Is Offline
Location: Morayfield Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 21st, 2013 at 07:02 AM |
|
|
| Quote: | Originally
posted by Craig Torrens
The new gear is for a type 1 motor, not a type 4.....so that's your problem !
Place your type 4 gear on a table with the chamfer side facing down. Position the key way slot in the 12 oclock position. At the 6 o'clock position
(opposite the keyway in a straight line) you will see a valley in the gears (bottom of the tooth).....now move one valley over to the left (towards 7
oclock) and that is where the dot on the cam should be placed.
send me your email and I can send you a pic.
|
Hey Craig,
Pm sent to you for the pic.
Cheers
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on December 21st, 2013 at 08:13 AM |
|
|
No pm at my end 
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on December 21st, 2013 at 09:04 AM |
|
|
Pics....I hope that helps.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
