| [ Total Views: 677 | Total Replies: 7 | Thread Id: 105433 ] |
|
|
 oldturtle22
Officially Full-On Dubber
Posts: 267
Threads: 57
Registered: November 26th, 2011
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 16th, 2014 at 10:16 AM |
|
|
Seat belts in Beetles.
Im looking at fitting seat belts to my Beetle. If anyones got pics of where and how your are fitted please post pics up. Thanks in advance
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on March 16th, 2014 at 10:29 AM |
|
|
What year Beetle?
62 and later has stock mounting points, although the upper sash mounts of 67 and earlier are way too low.
|
|
|
oldturtle22
Officially Full-On Dubber
Posts: 267
Threads: 57
Registered: November 26th, 2011
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 16th, 2014 at 01:56 PM |
|
|
Seat belts
Sorry it's a 59
|
|
|
pfillery
Insano Dub Head
Posts: 734
Threads: 160
Registered: December 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 16th, 2014 at 09:32 PM |
|
|
I don't think 59 had them so whatever you fit has to be engineered into there. I had a 66 that was set up for sash only belts so had the stalk
mounting in the central tunnel and the one above the shoulder, none for the bottom.
Mine had been retrofitted by plating under the floor, directly below the pillar. Only easy place I think unless you plan to weld points into the body
on the heater channel, still have to be engineered whichever way. I think that's why seatbelts are often still left off these things, any seatbelt
has to be better than none but the cost and red tape to engineer is too much.
Also seen plenty bolted through the pillar to put in the shoulder mount.
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on March 17th, 2014 at 08:36 AM |
|
|
Hi there,
this should help you as id did me with my 61 model.
http://www.thebugshop.org/bsp57_10.htm
And then click 'Resto Index' at the bottom centre of page for a lot more resto information.
Kev
|
|
|
oldturtle22
Officially Full-On Dubber
Posts: 267
Threads: 57
Registered: November 26th, 2011
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 17th, 2014 at 08:10 PM |
|
|
Seat belts
Thanx for that link Kev. Quite helpful
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 17th, 2014 at 09:30 PM |
|
|
Might be best to get that done before the interior goes in Chris! Don't really want to be peeling headliners and carpets back to weld around them...
If you need a little bit more time just let me know.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on March 17th, 2014 at 11:16 PM |
|
|
If you go 3 point inertia belts then the tricky part is the upper B pillar strengthener but for both upper and lower plates you need to cut a
letterbox opening in the side of the pillar to allow you to slip the strnegtheners in. I made some clamping plates of 8mm steel with 4 threaded holes
in the corners so I could flatten the curve of the pillar to allow the strengthener to sit properly and used the 4 holes to plug weld the
strengtheners in.
Tunnel can be done by welding thick wire to the strengther and then feeding it from the gear linkage cover down to the stalks mounting hole in the
tunnel and then plug welded in place.
All the strengthener plates must have radiused edges and need the 7/16 nut welded to the back of them for the seat belt bolts. 7/16 is the world wide
used standard for seat belts but so long as using high tensile bolts then M12 should work but you need fine thread M12 
madness is in the eye of the beholder  |
|
|
