| [ Total Views: 671 | Total Replies: 11 | Thread Id: 105752 ] |
|
|
 Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on April 13th, 2014 at 07:31 PM |
|
|
Issue assembling crank distributor drive gear
Hi all,
Just had the new crank in freezer, cam gear and spacer in oven and fitted them. The issue I have is in measuring the brass distributor gear and lock
ring, it is wider then the available space.
Yes, I have the cam gear on the correct way with marks facing pulley end and yes they appear to be home tight on their seats.
My Brass distributor drive is 11.3mm thick or 444 thou's of an inch, the locking clip is 2.38mm thick or 93 thou's of an inch.
Can anyone tell me if theirs is the same thickness, and if you were going to reduce either in thickness would you remove it from brass gear or the
clip.
I think you may say the spacer, but that is already pressed on 
I can't find any dimensions on the net re the brass gear thickness, hence why I am asking.
Thanks for you thoughts and feedback, Kev
EDIT: This is a Scat crank and Scat kit that I have.
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on April 13th, 2014 at 07:52 PM |
|
|
Always modify the cheapest part.
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on April 13th, 2014 at 08:36 PM |
|
|
| Quote: | Originally
posted by shokwave2
Always modify the cheapest part.
|
I like that 
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 13th, 2014 at 09:20 PM |
|
|
Just measured one at 11.17 Kev. Unfortunately I don't have many lying around as I always am using the old German ones as quickly as I get them.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on April 13th, 2014 at 09:32 PM |
|
|
Thanks Mat, sounds like everyone prefers a lot of the original German parts 
Your drive is about 0.15mm difference to mine and someone else told me there clip is about 0.3mm thinner than mine. That's .45mm and I am needing to
reduce by 0.5mm, so it all adds up. The gear drive, spacer and brass drive are all interference fit, so I guess if I take my clip down 0.5mm it
should all stay together ok.
Thanks for that, Kev
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 13th, 2014 at 09:44 PM |
|
|
Did you dress/debur your gears, if not, it might be wise and take the gear and spacer off and give thier faces a dress on a flat glass with 1200
paper. I would personally leave the clip except for deburring, and work the brass gear a little more if necessary. The drive runs on the middle of the
gear so shouldn't be an issue.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on April 14th, 2014 at 08:30 AM |
|
|
| Quote: | Originally
posted by matberry
Did you dress/debur your gears, if not, it might be wise and take the gear and spacer off and give thier faces a dress on a flat glass with 1200
paper. I would personally leave the clip except for deburring, and work the brass gear a little more if necessary. The drive runs on the middle of the
gear so shouldn't be an issue.
|
Hi Mat,
this would mean I have to take it somewhere and now get the gear and spacer pressed off. I still find it hard to fathom that everything you buy for a
vw needs to be reworked or checked. Not happy Jan
Thanks heaps for your knowledge, time and experience 
(Still learning) Kev
|
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on April 14th, 2014 at 08:49 AM |
|
|
Kev, did you ever wonder why it costs so much to have an engine built PROPERLY  
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
RodPenrose
A.k.a.: Rodney Penrose
Insano Dub Head
Posts: 792
Threads: 330
Registered: April 21st, 2005
Member Is Offline
Location: Kembla Grange, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: GETTING FASTER
|
| posted on April 14th, 2014 at 10:07 AM |
|
|
Kev , make sure that the heated crank gear is seated all the way home . They can creep if you don't hold weight on them until the cool a little . I
have never seen an issue with the Scat gear sets yet , however you may be the first . I use these all the time and the fitment is usually pretty good
, ROD.
More boost + More fuel = More power
1968 Beetle fastest run 8.96 sec @ 161 mph 4th Nov. 2001
2010 New Beetle 8.12 sec on 8th march 2014
http://www.rodpenroseracing.com.au
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on April 14th, 2014 at 10:13 AM |
|
|
Hi Kev
I have a special puller for the gears if you want to borrow it
Steve
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on April 14th, 2014 at 10:46 AM |
|
|
some shops build a motor, then some times pull them apart after just turning it over to check bearings etc or just do one run and pull down and check
clearances etc about 70 hours to build VW performance motor 
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on April 14th, 2014 at 11:53 AM |
|
|
Yep use origional Volkswagen gears then you wont have any problems
|
|
|
