| [ Total Views: 1058 | Total Replies: 6 | Thread Id: 105928 ] |
|
|
 Uncle Barry
Casual Dubber
Posts: 23
Threads: 5
Registered: July 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
 posted on May 2nd, 2014 at 11:32 AM |
|
|
Cam plug oil leak, rubber plug success?
Gday All,
Have done a engine rebuild and now the god dame engine cam plug has a small leak. New rear main fitted and its defiantly the cam plug. Use some dye
and uv light to prove once apart...
Rebuilt with a new plug but the cam gear shat it self and had to split again. So used the old new metal plug. Engine has done now about 20kms if
that.
So the rubber plug thats available has any one has some good, bad stories theyd like to share.
I really dont want to split the case again. Just loosing the rebuild a engine mojo and really want to drive it.
Used a brand spanking new bubble top case so no issues with it.
Cheers Uncle Baz
|
|
|
Uncle Barry
Casual Dubber
Posts: 23
Threads: 5
Registered: July 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 5th, 2014 at 01:16 PM |
|
|
well looks like no one has any horror stories. Ill give it a go.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on May 5th, 2014 at 03:15 PM |
|
|
The rubber plug is designed to fit a case that has no groove. The metal plug is for a grooved case. I've not tried fitting the rubber plug to a
grooved case but I think removing the old one without hurting the sealing area may be difficult. Sometimes I've seen the bearings and/or sealant
block the drain channel to create a leak, or when you had it apart to do the cam gear, the surfaces got oiled and didn't seal properly??
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Uncle Barry
Casual Dubber
Posts: 23
Threads: 5
Registered: July 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 7th, 2014 at 10:12 AM |
|
|
yeah the rubber plug suppliers say it can be used for both. Would have to use some premium sealant for sure. But splitting the case again would just
be the straw the broke the camels back. it would be a fire sale of car, and we have worked so hard to this point to do that and not get any enjoyment
out of the car. Id be prepared to give it a go with the knowledge of splitting the case in a few years. I could live with that. Interesting that not
more stories of cam plug leaks.
cheers.
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on May 7th, 2014 at 05:52 PM |
|
|
If it was me and it was a small leak, i'd drain the oil, clean the area and smear with the black Permatex sealant and let dry for a few days. Save
you from splitting the case. If it leaks again you have bigger issues.
|
|
|
Uncle Craig
Commited Dubber
Posts: 66
Threads: 11
Registered: June 13th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 23rd, 2016 at 01:36 PM |
|
|
well pulled the engine out and split the case. just as well as the cam plug oil return gallery was blocked with excessive sealant. reassembled and no
leak.
FB link to vid.
https://www.facebook.com/craigdrechsler/videos/1232918830104743/
I am sick of ABS, SRS, AFM, SIDI, ECU, PIM, BCM, Electronic sensors & actuators, scan tools, fault codes, programing, flashing, syncing, Drive by
wire, tract  ion & stability control, AARRHHH!!! Just give me
Air cooled, VW's.. Simple. |
|
|
fish26
A.k.a.: benito
Fahrvergnugen
Posts: 903
Threads: 38
Registered: July 13th, 2007
Member Is Offline
Location: sydney
Theme: UltimaBB Pro Grey
Mood: Ken awesome
|
| posted on November 23rd, 2016 at 08:59 PM |
|
|
Did you use silicone as sealant?
bitten by the bug..........several times
|
|
|
