| [ Total Views: 638 | Total Replies: 6 | Thread Id: 106392 ] |
|
|
 snowman9
Casual Dubber
Posts: 38
Threads: 10
Registered: December 7th, 2009
Member Is Offline
Location: Central Coast NSW
Theme: UltimaBB Streamlined2
Mood: Happy
|
| posted on June 19th, 2014 at 11:17 AM |
|
|
Type 1 main bearings
What's the story with main bearings these days?
After searching a few forums, I'm reading that the quality of available bearings has taken a dive - No. 2 main is no longer steel backed! Which
leaves me concerned and dismayed to say the least.
My late WD, AS41 case @ 0.50mm over, has been running the same bottom end for over 13 years (have split it to replace cam & lifters only in 2008).
I've ordered a 69mm CW crank from DPR machine and they can supply steel backed Silverline mains. My concern is that I've read else where that their
No.2 steel backed shells do not have a 360° groove at the crank surface.
I'm not sure of the sizes I will require, the case may need line boring to 0.75 and the crank isn't done yet so I don't know how far under it'll
be. I've found that in the past, odd sizes were sometimes difficult to source from either Tooleys or Fermans.
The set that's been running in this motor was sourced from Lionel (RIP): one gruff old bastard, but one of the nicest blokes in the VW trade I've
ever had dealings with. I miss him, but I digress.
So, are steel backed Mahle items still kickin' round on our sunny shores in maybe 0.50 / 0.75mm on the case & either 0.25/0.50mm on the crank ?
Any help is much appreciated.
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on June 19th, 2014 at 11:27 AM |
|
|
Just to add, even the genuine vw main bearings (standard sized) are not all too flash either. The machine shop that checked clearances said they were
quite inconsistant with their tolerances.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 19th, 2014 at 04:10 PM |
|
|
Yep, RIP Lionel, he was a top bloke to deal with. 
I haven't needed to use them yet, but I believe the Silverline are the ones to use if your avoiding the non-steel backed
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on June 19th, 2014 at 05:45 PM |
|
|
I have a few sets of silverline bearings with a set in my 2276 and set currently being fitted to a 2054, same issues with the bearing tolerance, a bit
hit and miss.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 19th, 2014 at 07:19 PM |
|
|
| Quote: |
The set that's been running in this motor was sourced from Lionel (RIP): one gruff old bastard
|
Which Lionel was that
Check with a few of the shops you may find some goodies
|
|
|
snowman9
Casual Dubber
Posts: 38
Threads: 10
Registered: December 7th, 2009
Member Is Offline
Location: Central Coast NSW
Theme: UltimaBB Streamlined2
Mood: Happy
|
| posted on June 20th, 2014 at 09:29 AM |
|
|
Lionel Francis Dave, ex Fermans.
Yep, I'll do some chasing today.
Indeed Matt, I think I'd rather stick needles in my eyes than take the chance and use non - steel backed shells on No. 2. But, there's still the
issue of the absence of a 360° groove on the crank side.
Does anyone have any thoughts on this ?
Thank you for your replies Gentlemen
|
|
|
snowman9
Casual Dubber
Posts: 38
Threads: 10
Registered: December 7th, 2009
Member Is Offline
Location: Central Coast NSW
Theme: UltimaBB Streamlined2
Mood: Happy
|
| posted on June 21st, 2014 at 01:36 PM |
|
|
| Quote: | Originally
posted by snowman9
But, there's still the issue of the absence of a 360° groove on the crank side.
Does anyone have any thoughts on this ?
|
Sorry folks. Please disregard - was having a flash back to centre main bearings on Clevelands'.
Must be gettin' old 'n' doddery. WTF?
|
|
|
