| [ Total Views: 1045 | Total Replies: 8 | Thread Id: 107265 ] |
|
|
 tintoy
Commited Dubber
Posts: 72
Threads: 46
Registered: April 27th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 23rd, 2014 at 12:21 PM |
|
|
Allen Key door hinge bolt removal HELP!
HELP - For the life of me I cannot remove the Allen Key door hinge bolts on my type III. The bolts are starting to become rounded.
Ideas???? Please!!!
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on September 23rd, 2014 at 12:56 PM |
|
|
Hmm, how to describe this method that I have used , though not on hinge bolts. Get a small coal (cold?) chisell, sharpen it to a "blunt" angle
(about 60-80 deg) then holding it on one side of the screw head and at an angle that will allow the chisel to bite into the head of the screw start
taping it firmly so that it turns the screw in the direction to unscrew it (anticlockwise ?). The screw will loosen and then you can use the Allen key
to finish the job. Mind you, the screw head will be stuffed. 
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on September 24th, 2014 at 08:58 AM |
|
|
Yes Don its a cold chisel like Jimmy Barnes.. lol..
although I've never ever seen anyone using a HOT chisel.. lol
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
tintoy
Commited Dubber
Posts: 72
Threads: 46
Registered: April 27th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 24th, 2014 at 09:08 AM |
|
|
Thanks guys will give it a try however will be a task as bolts are set inside the pillar.
|
|
|
1500S
Custom Title Time!
Posts: 1418
Threads: 73
Registered: March 28th, 2005
Member Is Offline
Location: Nth Richmond, N.S.W
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 24th, 2014 at 09:37 AM |
|
|
| Quote: | Originally
posted by tintoy
Thanks guys will give it a try however will be a task as bolts are set inside the pillar.
|
Make a flat head punch from a piece of 1/2" diameter steel x about 6" long. Give each screw a few hits with a hammer on the punch to break the rust
on the thread and underneath of head. Maybe use an impact driver as well to undo screws.
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on September 24th, 2014 at 11:59 AM |
|
|
Failing this get an M8 key (star spline) socket and hammer it in to the rounded allan key hole and unscrew.
M8 is the same tool to undo the IRS axle bolts
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on September 24th, 2014 at 10:33 PM |
|
|
| Quote: | Originally
posted by donn
Hmm, how to describe this method that I have used , though not on hinge bolts. Get a small coal (cold?) chisell, sharpen it to a "blunt" angle
(about 60-80 deg) then holding it on one side of the screw head and at an angle that will allow the chisel to bite into the head of the screw start
taping it firmly so that it turns the screw in the direction to unscrew it (anticlockwise ?). The screw will loosen and then you can use the Allen key
to finish the job. Mind you, the screw head will be stuffed.
|
I can vouch for this method. Works well.
Also heating the head with blow torch works wonders but i think you might burn the paint on the car.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
bushed
Wolfsburg Elder
Posts: 3539
Threads: 66
Registered: December 18th, 2006
Member Is Offline
Location: Lowood Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 25th, 2014 at 02:21 PM |
|
|
first tap the bolt on the head to scare (shock) it through the thread
works on most BIG bolts and a good vice grip can help when locked on well
want any vw bits old but like me, Made in Germany!!!
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on September 26th, 2014 at 09:47 PM |
|
|
vice grips wont be getting in where those screws are lol.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
