| [ Total Views: 1172 | Total Replies: 5 | Thread Id: 108763 ] |
|
|
 clyve
Officially Full-On Dubber
Posts: 310
Threads: 93
Registered: February 19th, 2011
Member Is Offline
Location: sunshine coast
Theme: UltimaBB Pro Blue ( Default )
Mood: painfully happy
|
| posted on April 8th, 2015 at 06:08 PM |
|
|
front end
Hello all
I am after some info and help, I have a 67 beetle with king pin front.
It has disc on the front, four stud! Pattern but re drilled to porsche stud pattern
Ok so here is the questions
Will it pas road worthey in qld with the re-drills?if not where to buy pre drilled to right patteren?
Best way to lower front? It has the lowering adjusters in the beams but dont seem to do anything? Worth stripping back?
Do you need shorter shocks?
Can I retro fit twin master cylinder on the brakes ?
And finaly the wire loom goes over the roof in the channel is this right
Thanks for the help will post a thread this week
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 8th, 2015 at 06:18 PM |
|
|
As for the lowering... I have a 1966 K&L Pin Beetle, and i bought a set of drop spindles from Mick Motors.
Drops it 2 1/2 Inches, and no problems getting them on.
My Members ride is here
About half way down...
JMO, but works and looks great.
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 8th, 2015 at 06:22 PM |
|
|
And no, i dont have shorter shocks. The standards seem to be fine for me. 
|
|
|
clyve
Officially Full-On Dubber
Posts: 310
Threads: 93
Registered: February 19th, 2011
Member Is Offline
Location: sunshine coast
Theme: UltimaBB Pro Blue ( Default )
Mood: painfully happy
|
| posted on April 8th, 2015 at 07:49 PM |
|
|
,like
Yep looks sweet much difference on handeling?
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 8th, 2015 at 08:25 PM |
|
|
Haven't actually got it on the road yet  but have
heard from many that the lower to the ground the better they handle.. Look and circuit cars and formula V's for example...
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on April 9th, 2015 at 07:22 AM |
|
|
If you have a disc brake conversion it will require a dual circuit master cylinder, you should not redrill the standard rotors is the casting is to
thin and depending on the place of road worthy it might fail during the inspection, lowering the car does not guarantee an improvement in handling, A
lot of other factors have to be considered like castor angle, toe, condition of the front end.
|
|
|
