| [ Total Views: 3476 | Total Replies: 6 | Thread Id: 109392 ] |
|
|
 69notch
Learner Dubber
Posts: 3
Threads: 1
Registered: June 1st, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 2nd, 2015 at 11:44 PM |
|
|
primer to top coat steps?????
Hi Guys
about to start the prep work on my notch and need some info.
car was blasted and primed around 5 years ago and has been sitting since due to lack of time.
the inside and under guards have all been 2k but still the roof, guards, doors, front and rear panels are in primer.
i plan to sand them back to bare metal due to surface rust and length of time they have been sitting in primer and treat but not sure where to go
after that am i right to say the steps are
1 metal treatment
2 epoxy prime
3 body filler
4 thin coat of epoxy to seal filler
5 high build filler
6 block sand and guide coat
7 topcoats
have been searching through the forum but they all seem to come up short so any help would be great.
Cheers kyle |
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on July 3rd, 2015 at 12:04 AM |
|
|
The steps you have listed is in short terms pretty much how we do restorations at work. You are right in removing the primer that is already on the
car it has been on too long unprotected, and primer is porous. We use Epotec 408 Epoxy primer, 4 to five coats. Rub the Epotec with 120 grit,
Polyester filler as required, One coat of Epoxy on the bare metal rub throughs and the filler to seal up, Hi build primer, and so on.
|
|
|
69notch
Learner Dubber
Posts: 3
Threads: 1
Registered: June 1st, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 3rd, 2015 at 01:34 PM |
|
|
thanks for the reply.
now i know im on the right track its time to get to work. |
|
|
Governor
Wolfsburg Wizard
Posts: 414
Threads: 23
Registered: November 22nd, 2008
Member Is Offline
Location: in your mind
Theme: UltimaBB Pro Blue ( Default )
Mood: yes please
|
| posted on July 3rd, 2015 at 05:14 PM |
|
|
I have used Epotec and its great stuff
|
|
|
helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on July 3rd, 2015 at 07:02 PM |
|
|
Just remember the Epotec epoxy will stick to EVERYTHING. You will need to plastic cover all walls, the floor, the ceiling, and don't wear any clothes
or shoes you want to keep nice. Wear a proper Sundstrom type cannister breathing mask. Wear Nitrile gloves. Once you have finished cleaning the spray
gun, go straight inside and have a good long hot shower. It makes your eyelashes stick together even.
|
|
|
69notch
Learner Dubber
Posts: 3
Threads: 1
Registered: June 1st, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 4th, 2015 at 12:09 PM |
|
|
wow thats some sticky stuff, i was going to lay plastic on the floor, walls and roof but i mite even wrap myself now. |
|
|
lou0060
Wolfsburg Wizard
Posts: 568
Threads: 30
Registered: December 12th, 2010
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 5th, 2015 at 06:08 PM |
|
|
don't forget I've got that full face mask....
1971 karmann ghia Cabrio - Cruising 
1963 beetle Sunroof - gathering dust 
1968 race beetle - twin turbo Subaru - stress relief 
1960 beetle - old school low & slow  |
|
|
