| [ Total Views: 1024 | Total Replies: 11 | Thread Id: 111691 ] |
|
|
 gregory
Casual Dubber
Posts: 37
Threads: 30
Registered: October 25th, 2014
Member Is Offline
Location: Grafton.. nth NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 20th, 2016 at 06:00 PM |
|
|
HELP with camber adjustment
Help needed.......
70 Beetle.
Just tried to get a wheel alignment done. Left side is OK, BUT they can't get the correct Camber on the right side. The adjustment goes from 4 1/2
degrees positive to 1 1/12 degrees positive. Won't go any lower than 1 1/2..
Any ideas of where the fault could be?
Have not long had it, so no idea of history.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 20th, 2016 at 06:27 PM |
|
|
Check the 4 ball joints first for wear or loose u need a VW tool to do this under load
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on October 20th, 2016 at 09:33 PM |
|
|
Pop the balljoints from the spindle. You'll be able to tell by hand if they're knackered or not. Sloppy or really loose is no good. Unless very new
then they should still have some resistance when you move the ball in it's socket.
If the joints are OK then you next have to check the torsion arm bearings and finally see if the lower arm is bent as a heavy curbing can bend them.
madness is in the eye of the beholder  |
|
|
AA003
A.k.a.: Phill
Custom Title Time!
Posts: 1189
Threads: 39
Registered: October 27th, 2011
Member Is Offline
Location: Southern Highlands
Theme: UltimaBB Streamlined2
|
| posted on October 21st, 2016 at 05:10 AM |
|
|
Something is bent. Have a good look at the arms. The person doing the wheel alignment should be able to work out what is wrong.
I read it on samba, so it must be correct.
Sometimes Volkswagen dealers sell spare parts. Amazing isn't it!
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on October 21st, 2016 at 07:05 AM |
|
|
Has the beam been cut and welded for lowering, if not done correctly the leaves can be off set to one side, you can buy adjusters with more camber but
its better to find the cause first
|
|
|
gregory
Casual Dubber
Posts: 37
Threads: 30
Registered: October 25th, 2014
Member Is Offline
Location: Grafton.. nth NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 29th, 2016 at 07:27 PM |
|
|
UPDATE.....
found the right lower balljoint was sloppy, so replaced both upper and lower.
Back for another try at wheel aligning......... Still cannot get the right side camber right.
So now going to TRY to see if something is bent.
|
|
|
AA003
A.k.a.: Phill
Custom Title Time!
Posts: 1189
Threads: 39
Registered: October 27th, 2011
Member Is Offline
Location: Southern Highlands
Theme: UltimaBB Streamlined2
|
| posted on October 30th, 2016 at 06:03 AM |
|
|
Go somewhere else for a wheel alignment. If the retard couldn't work out that the ball joint was worn, I wouldn't be letting him touch my car.
I read it on samba, so it must be correct.
Sometimes Volkswagen dealers sell spare parts. Amazing isn't it!
|
|
|
gregory
Casual Dubber
Posts: 37
Threads: 30
Registered: October 25th, 2014
Member Is Offline
Location: Grafton.. nth NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 30th, 2016 at 06:58 AM |
|
|
| Quote: | Originally
posted by AA003
Go somewhere else for a wheel alignment. If the retard couldn't work out that the ball joint was worn, I wouldn't be letting him touch my car.
|
VERY good point!
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 30th, 2016 at 05:38 PM |
|
|
| Quote: |
Check the 4 ball joints first for wear or loose u need a VW tool to do this under load
|
As I said it has to be checked with VW tool under load
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on October 30th, 2016 at 10:10 PM |
|
|
Yea, I had a guy get the total toe right but the individual was totally ballsed up.
It ain't rocket science but alas there are some folks who have trouble tying their shoes 
madness is in the eye of the beholder |
|
|
gregory
Casual Dubber
Posts: 37
Threads: 30
Registered: October 25th, 2014
Member Is Offline
Location: Grafton.. nth NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 11th, 2016 at 05:30 AM |
|
|
All sorted. Thanks for the help.
Turned out to be bent control arms..
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 11th, 2016 at 03:52 PM |
|
|
| Quote: | Originally
posted by gregory
All sorted. Thanks for the help.
Turned out to be bent control arms..
|
Glad you got to the bottom of it
madness is in the eye of the beholder |
|
|
