| [ Total Views: 1020 | Total Replies: 8 | Thread Id: 111703 ] |
|
|
 wombatventures
Wolfsburg Wizard
Posts: 680
Threads: 44
Registered: February 11th, 2013
Member Is Offline
Location: Peterborough SA
Theme: UltimaBB Pro Orange
Mood: BUSted, BUGgered & NOTCHed
|
| posted on October 24th, 2016 at 08:08 AM |
|
|
Clean rust from Fuel tank with Vinegar
Foud a few mentions of using Vinegar as a rust converter in steel fuel tanks.
Has anyone done this and if so how did it go?
I use vinegar water to convert rust on light steal, rub down surface rusted panels and similar but have not considered the fuel tank until now.
I've got the tank out of the Notch and will take the sender out today, drop in some chain and a few nuts and give it a rattle around. Looks pretty
clean inside but the mesh filter was pretty cruddy and choked. The filler inlet seams to have the worst rust.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on October 24th, 2016 at 03:15 PM |
|
|
Timely question, since I'm plotting and scheming to do mine too before dropping it back in.
Dunno about vinegar Mr Wombat, but I do know something that is absolutely guaranteed to work with removing rust..........on old extractors anyway!
My son-in-law got hold of 20L of molasses from a horsey joint and filled 1/2 a 44, then dropped in his rusty old pipes off his old Datto.
Came back home off-swing 3 weeks later, and they looked as shiny as new! I had heard that the stuff worked, but until I saw it in steel it was
difficult to imagine just how effective the stuff is.
Oh, and I'm unsure if he used it straight or cut with water, a G@@gle-Fu would tell you I spose.
|
|
|
wombatventures
Wolfsburg Wizard
Posts: 680
Threads: 44
Registered: February 11th, 2013
Member Is Offline
Location: Peterborough SA
Theme: UltimaBB Pro Orange
Mood: BUSted, BUGgered & NOTCHed
|
| posted on October 24th, 2016 at 05:23 PM |
|
|
9 litres water, 1 litre molasses. Works brilliant but you have to treat the metal as soon as you wash it off. Give it a coat of wd40 or something to
stop it from re oxidising.
Was hoping I could clean the tank this week and back in asap. Watched a couple of videos using vinegar then rinsing. I'm mosty worried it will etch
the tank too much.
This is a good video for the Molasses Trick
https://youtu.be/KZCFcxf5IBw
|
|
|
Phil74Camper
Son of Jim - Creator of Good
Head in the Clouds
Posts: 2703
Threads: 193
Registered: August 28th, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 26th, 2016 at 06:08 PM |
|
|
Vinegar is mostly diluted acetic acid, so it would attack the metal as any other acid would. People have tried using Coke as well - it's also acetic
acid but a lot more dilute than vinegar, which is around 20%. I don't think acetic acid would 'convert' the rust at all - just slowly dissolve the
steel underneath.
Rust converters also have acids in them, but usually phosphoric acid or tannic acid. These change the iron oxide to ferric phosphate or ferric
tannate, which are more stable and basically inert.
|
|
|
wombatventures
Wolfsburg Wizard
Posts: 680
Threads: 44
Registered: February 11th, 2013
Member Is Offline
Location: Peterborough SA
Theme: UltimaBB Pro Orange
Mood: BUSted, BUGgered & NOTCHed
|
| posted on October 27th, 2016 at 05:59 AM |
|
|
That's similar to what I was thinking Phil.
I think its more for etching the rust off the surface as they say to neutralise the tank after rinsing with baking soda (bicarb) then rinsing with
demineralised water to flush all the chemicals before reusing the tank.
Would rust converter form a stable enough coating after treating a tank and would it need to be flushed to stop the process?
I've used rust converter on floor pans to stabilise them. Leaves a nice hard grey/black oat of ferric phosphate that lasts ages even when pinted
over. Would that layer last in the tank with no covering and would our modern unleaded fuel chemistry affect it?
|
|
|
Phil74Camper
Son of Jim - Creator of Good
Head in the Clouds
Posts: 2703
Threads: 193
Registered: August 28th, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 27th, 2016 at 05:16 PM |
|
|
I'd be trying to seal the insides once its been cleaned, rust converted, neutralised, rinsed and dried. Maybe some POR-15 thinned down and sloshed
around inside, then left to drain and dry? Obviously you'd need the tank out of the car so it can be shaken, rotated and turned over as required.
|
|
|
silver
Veteran Volks Folk
Dangerous when poked
Posts: 2169
Threads: 162
Registered: December 8th, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: In 2 Minds
|
| posted on October 27th, 2016 at 08:49 PM |
|
|
Home made electroplating cleans and coats your tank
google it there is a couple of ideas
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
Keeping it real !
|
|
|
wombatventures
Wolfsburg Wizard
Posts: 680
Threads: 44
Registered: February 11th, 2013
Member Is Offline
Location: Peterborough SA
Theme: UltimaBB Pro Orange
Mood: BUSted, BUGgered & NOTCHed
|
| posted on October 28th, 2016 at 12:21 PM |
|
|
| Quote: | Originally
posted by Phil74Camper
I'd be trying to seal the insides once its been cleaned, rust converted, neutralised, rinsed and dried. Maybe some POR-15 thinned down and sloshed
around inside, then left to drain and dry? Obviously you'd need the tank out of the car so it can be shaken, rotated and turned over as required.
|
Tank out was simple. Did it before I took the bottom filter out.
Undo fuel line and drain.
Pop bonnet and remove mat.
Unscrew clamps on breather and filler and unplug guage sender wire.
4 bolts then lift out tank.
Thank you Wolfsburg for simplicity!
|
|
|
wombatventures
Wolfsburg Wizard
Posts: 680
Threads: 44
Registered: February 11th, 2013
Member Is Offline
Location: Peterborough SA
Theme: UltimaBB Pro Orange
Mood: BUSted, BUGgered & NOTCHed
|
| posted on October 28th, 2016 at 12:25 PM |
|
|
| Quote: | Originally
posted by silver
Home made electroplating cleans and coats your tank
google it there is a couple of ideas
|
Like the idea of doing the inside of the tank. Where did you find the info?
|
|
|
