| [ Total Views: 1698 | Total Replies: 11 | Thread Id: 112855 ] |
|
|
 samjo
Learner Dubber
Posts: 16
Threads: 4
Registered: October 5th, 2017
Member Is Offline
Location: Tasmania
Theme: UltimaBB Powder
|
| posted on October 9th, 2017 at 06:25 PM |
|
|
Head replacement (stock)
Hi all,
Had a bit of a look around in other topics, but couldn't find what I'm looking for.
I got a 70 Fastback and want to replace the head (burnt valve).
Is it possible to remove the head with the engine in place or does it have to come out?
Also has anyone used one of the various stock replacement heads and recommend one or are most people reconditioning the existing heads.
Now I know that it probably would be better to recondition the whole engine but at this stage I dont have the finances to do so and need my daily
driver back on the road.
Any advise would be appreciated.
regards, samjo
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 9th, 2017 at 06:31 PM |
|
|
Yes it is possible to remove the heads while engine is in place
HOWEVER
Its easier and quicker to remove the engine to work on it on the bench as it will take half the time, and with VWs if you are removing one side
then its best to remove the other side as well.. as you will find its probably beggared as well
You will have to replace a fair few gaskets as well
where r u at
|
|
|
samjo
Learner Dubber
Posts: 16
Threads: 4
Registered: October 5th, 2017
Member Is Offline
Location: Tasmania
Theme: UltimaBB Powder
|
| posted on October 9th, 2017 at 06:58 PM |
|
|
It's kind of what I expected. You could probably get it out in a couple of hours and work would be so much easier.
Was under the impression that a head gasket is not required, that leaves inlet and exhaust gaskets. Anything else?
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 10th, 2017 at 07:01 AM |
|
|
I have just taken the heads off a Type 3 motor which was on my engine stand - what a pain in the arse. Can not believe how much stuff has to come off.
Would never attempt it in the car.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 10th, 2017 at 07:15 AM |
|
|
push rod tube gaskets, oil cooler seal, rocket cover gaskets might as well do the rear seal while yr in there
and check both heads while its out also replace the valve guides and check the heads for cracks
may be cheaper to get some new heads in the long run
|
|
|
samjo
Learner Dubber
Posts: 16
Threads: 4
Registered: October 5th, 2017
Member Is Offline
Location: Tasmania
Theme: UltimaBB Powder
|
| posted on October 10th, 2017 at 05:31 PM |
|
|
Anyone bought from the two listed suppliers before, or can make recommendations for suppliers?
Rod Penrose Racing http://rodpenroseracing.com.au/standard-heads/141-dual-port-heads-steel-valve...
or
VDUB Depot http://www.vwperformance.com.au/engine/rockers-heads-valves-hardware
|
|
|
waltermitty
Custom Title Time!
Legend when my beer goggles are on
Posts: 1993
Threads: 268
Registered: August 29th, 2002
Member Is Offline
Location: Port Macquarie now Yipee!
Theme: UltimaBB Pro Grey
Mood: Hungry for mor
|
| posted on October 10th, 2017 at 06:36 PM |
|
|
https://youtu.be/gKF6dcKjLJo
23 windows ...8 too many!
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on October 11th, 2017 at 06:40 PM |
|
|
| Quote: | Originally
posted by samjo
Hi all,
Had a bit of a look around in other topics, but couldn't find what I'm looking for.
I got a 70 Fastback and want to replace the head (burnt valve).
Is it possible to remove the head with the engine in place or does it have to come out?
Also has anyone used one of the various stock replacement heads and recommend one or are most people reconditioning the existing heads.
Now I know that it probably would be better to recondition the whole engine but at this stage I dont have the finances to do so and need my daily
driver back on the road.
Any advise would be appreciated.
regards, samjo
|
Samjo a few years ago I replaced the No 3/4 cylinder head on my brother in laws type 3 in the car park at a servo on the f3. it wasn't that hard just
a bit of time involved, I loosened the exhaust,slid it back,removed the carb and manifold,tinware etc and slid the head off. i then drove to Tooleys
at Hornsby, purchased a head and seals, fitted these in situ and he drove away for another couple of years and forgot to pay me for the parts. Nice
and easy;.l No dramas if you are prepared to do it.
|
|
|
bushed
Wolfsburg Elder
Posts: 3539
Threads: 66
Registered: December 18th, 2006
Member Is Offline
Location: Lowood Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 11th, 2017 at 09:22 PM |
|
|
| Quote: | Originally
posted by samjo
It's kind of what I expected. You could probably get it out in a couple of hours and work would be so much easier.
Was under the impression that a head gasket is not required, that leaves inlet and exhaust gaskets. Anything else? I'm too far south (Tassie)
|
as you have it all out its worth checking oil cooler rubber seals and if the other head is tight and then reset tappets
see the clutch wear (2 hrs extra work so you wont need to do it all again in a few months or years!
time is money...
preventive maintenance. enjoy and connect the heater right lol,
want any vw bits old but like me, Made in Germany!!!
|
|
|
samjo
Learner Dubber
Posts: 16
Threads: 4
Registered: October 5th, 2017
Member Is Offline
Location: Tasmania
Theme: UltimaBB Powder
|
| posted on October 13th, 2017 at 05:09 PM |
|
|
Is it easy to replace the rings while the heads are off or is that a very involved task?
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 14th, 2017 at 02:43 AM |
|
|
Fairly easy - but care is needed.
Lots of good reading here
http://www.vw-resource.com/engine_rebuild.html
Also YouTube is your friend
Futue te ipsum!!!
|
|
|
samjo
Learner Dubber
Posts: 16
Threads: 4
Registered: October 5th, 2017
Member Is Offline
Location: Tasmania
Theme: UltimaBB Powder
|
| posted on October 17th, 2017 at 07:13 PM |
|
|
Are the Type 3 1600 engines all dual port heads? I think I have read somewhere that some are single port but can't find it anymore.
|
|
|
