| [ Total Views: 809 | Total Replies: 5 | Thread Id: 17916 ] |
|
|
 Andy42
Insano Dub Head
Posts: 709
Threads: 47
Registered: March 13th, 2003
Member Is Offline
Location: Airlie Beach
Theme: UltimaBB Pro Blue ( Default )
Mood: 2.5t Subi Powered
|
| posted on January 18th, 2004 at 05:30 PM |
|
|
What is the best material for a kombi interior
Whas just wonderin what you guys recon is the go here. Obviously not bloody chip board again but I was thinking of marine ply but it might weigh a bit
much. Mainly just to replace the stuffed chip board sections not a complete refit.
.
|
|
|
Casper
Seriously Crusin Dubber
Posts: 185
Threads: 64
Registered: July 12th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 18th, 2004 at 06:34 PM |
|
|
Material to use for interior
We used plywood for our interior and pine for the benchtop. We put stain on the pine and a clear varnish on cupboards and bench top, trimmed it with
a decorative wooden trim and it looks Mickey Mouse. We live at Boondall Brisbane if you want to take a look. I know you said you were not doing a
refit, but if you or anyone else wants some good ideas for interiors check out http://www.calypsocampers.com for great ideas.
P Laxton
|
|
|
Adam_C
Custom Title Time!
Posts: 1180
Threads: 164
Registered: May 22nd, 2003
Member Is Offline
Location: Bargo, 1hr south of syd
Theme: UltimaBB Pro Blue ( Default )
Mood: could be lower
|
| posted on January 19th, 2004 at 12:07 PM |
|
|
if your painting it, then i would go for mdf, cheap easy to use and once painted looks great
Adam
Adzslick@iprimus.com.au
|
|
|
mnsKmobi
Wolfsburg Wizard
Posts: 589
Threads: 27
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 20th, 2004 at 11:53 AM |
|
|
Been thinking of doing the same thing. I could not believe how heavy the original chipboard is! To save weight I'm going to use thin plywood as
much as possible. MDF would be OK but I want to keep the "wood grain" look and the simplest way to do it is to put a clear coat on plywood.
|
|
|
vwtyp2
Son of Jim - Creator of Good
Posts: 2504
Threads: 160
Registered: September 18th, 2003
Member Is Offline
Location: Hillcrest S.A.
Theme: UltimaBB Pro Blue ( Default )
Mood: over it
|
| posted on January 20th, 2004 at 09:36 PM |
|
|
mdf is easy to work with and lighter than the same thickness of ply. also bends easier for kick panels etc.
Most people seem normal, till you get to know them.
|
|
|
Hbbear
Seriously Crusin Dubber
Posts: 171
Threads: 13
Registered: October 17th, 2003
Member Is Offline
Location: Jerra (NSW/ACT Border, On The Right Side)
Theme: UltimaBB Pro Blue ( Default )
Mood: Chillin' (what would you expect in Canberra?)
|
| posted on January 21st, 2004 at 10:26 AM |
|
|
MDF
A bit of advice when using MDF....
Our local hardware shops here in Canberra WILL NOT cut down MDF boards. It poses an OH&S issue apparently. If you plan on using MDF then may I
suggest 1. do it outside in well ventilated area 2. wear a face mask (just to cover nose/mouth). Having said this the mother inlaw(outlaw) uses MDF
for craft applications quite often, so dont let me put you off!
Winter is here.........Footy is here........now where is my beer.........
|
|
|
Adam_C
Custom Title Time!
Posts: 1180
Threads: 164
Registered: May 22nd, 2003
Member Is Offline
Location: Bargo, 1hr south of syd
Theme: UltimaBB Pro Blue ( Default )
Mood: could be lower
|
| posted on January 21st, 2004 at 12:46 PM |
|
|
yeh the glue the holds ti together contains a form of fromaldehide (SP?) i think, nt good, but adust mask and no probs 
Adam
Adzslick@iprimus.com.au
|
|
|
baybuscamperkid
Compulsive Aussie Vee Dubber
prince of insufficient light, ruler of heck
Posts: 4316
Threads: 335
Registered: August 25th, 2002
Member Is Offline
Location: Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: transported
|
| posted on January 24th, 2004 at 08:59 PM |
|
|
ive used a mix, MDF for the cabinet doors and benchtops, ply for the shelves and cubboard sides. ply is stronger and will survive water better, but
is heavier. i will be using ply for my door trims.
Reimagined/Recycled/Upcycled Cool
|
|
|
