| [ Total Views: 893 | Total Replies: 5 | Thread Id: 21126 ] |
|
|
 volks67
A.k.a.: Bob Priestley
Commited Dubber
Posts: 56
Threads: 20
Registered: June 8th, 2003
Member Is Offline
Location: wynnum west brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
 posted on April 5th, 2004 at 07:19 PM |
|
|
Rust repairs to Beetle
Guru's, Please assist with some advise.
My 67 Beetle has rust in the A Pillars and Heater channels. I have new replacement heater channels and lower sections of the A Pillars.
The body is off the floor pan as I have already replaced both floor pans halves.
Also have new replacement panels from the A Pillar to the front bulkhead and connect onto the heater channels .
I realise it is a lot of work but convinced that I will make the beetle stronger than original.
The advise I require would you tackle the A Pillars and inner guard replacement panels first or the heater channels first.
Further I intend to put intrusion bars in the rear quarters (25mm square ) and 50mm X3mm mild steel in the doors and across the roof evenly spaced
from the A Pillar.
I realise it will be a bit heavier than original but the idea is to bring it up to modern crash test standard.
catch you soon,
bob
|
|
|
volks67
A.k.a.: Bob Priestley
Commited Dubber
Posts: 56
Threads: 20
Registered: June 8th, 2003
Member Is Offline
Location: wynnum west brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on April 5th, 2004 at 07:20 PM |
|
|
Rust repairs to Beetle
Guru's, Please assist with some advise.
My 67 Beetle has rust in the A Pillars and Heater channels. I have new replacement heater channels and lower sections of the A Pillars.
The body is off the floor pan as I have already replaced both floor pans halves.
Also have new replacement panels from the A Pillar to the front bulkhead and connect onto the heater channels .
I realise it is a lot of work but convinced that I will make the beetle stronger than original.
The advise I require would you tackle the A Pillars and inner guard replacement panels first or the heater channels first.
Further I intend to put intrusion bars in the rear quarters (25mm square ) and 50mm X3mm mild steel in the doors and across the roof evenly spaced
from the A Pillar.
I realise it will be a bit heavier than original but the idea is to bring it up to modern crash test standard.
catch you soon,
bob
|
|
|
volks67
A.k.a.: Bob Priestley
Commited Dubber
Posts: 56
Threads: 20
Registered: June 8th, 2003
Member Is Offline
Location: wynnum west brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on April 5th, 2004 at 07:22 PM |
|
|
Rust repairs to Beetle
Guru's, Please assist with some advise.
My 67 Beetle has rust in the A Pillars and Heater channels. I have new replacement heater channels and lower sections of the A Pillars.
The body is off the floor pan as I have already replaced both floor pans halves.
Also have new replacement panels from the A Pillar to the front bulkhead and connect onto the heater channels .
I realise it is a lot of work but convinced that I will make the beetle stronger than original.
The advise I require would you tackle the A Pillars and inner guard replacement panels first or the heater channels first.
Further I intend to put intrusion bars in the rear quarters (25mm square ) and 50mm X3mm mild steel in the doors and across the roof evenly spaced
from the A Pillar.
I realise it will be a bit heavier than original but the idea is to bring it up to modern crash test standard.
catch you soon,
bob
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on April 5th, 2004 at 10:03 PM |
|
|
I don't think it would matter which part you did first. If they weld to each other in any way, then you really would have to do both at the same
time. The only thing I amaware of that you really need to take care with is making sure you dont let the body sag or open up when the heater channel
is cut off.
With the intrusion bars, be wary about how you design them as it would be very unfortunate if one of the ends of the bar comes off and it pivots and
becomes like a spear.
The extra weight from what you are putting in will not be noticed very easily. It wouldn't weight more than half a tank of petrol.
|
|
|
Robo
Compulsive Aussie Vee Dubber
Posts: 4491
Threads: 120
Registered: February 13th, 2003
Member Is Offline
Location: Tweed Heads
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval madness
|
| posted on April 6th, 2004 at 06:48 AM |
|
|
Her's some pictures of the bracing that is required when you are removing the old and welding in new heater channels.
Rob...
Boxer Power
Member of DMLRK.....Die Mittler Lebuns Resto Komeradschaft
 |
|
|
Robo
Compulsive Aussie Vee Dubber
Posts: 4491
Threads: 120
Registered: February 13th, 2003
Member Is Offline
Location: Tweed Heads
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval madness
|
| posted on April 6th, 2004 at 06:50 AM |
|
|
Next
Boxer Power
Member of DMLRK.....Die Mittler Lebuns Resto Komeradschaft
|
|
|
Robo
Compulsive Aussie Vee Dubber
Posts: 4491
Threads: 120
Registered: February 13th, 2003
Member Is Offline
Location: Tweed Heads
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval madness
|
| posted on April 6th, 2004 at 06:54 AM |
|
|
If those pictures are too big could someone make them smaller instead of deleteing them, I am sure some PPL would benifit from seeing them.
Rob...
Boxer Power
Member of DMLRK.....Die Mittler Lebuns Resto Komeradschaft
|
|
|
Stanley
Compulsive Aussie Vee Dubber
I guess the reward is in the doing of it
Posts: 4523
Threads: 270
Registered: March 13th, 2003
Member Is Offline
Location: Karalee...near Ipswich Qld
Theme: UltimaBB Psyche Grey
Mood: caught a bolt of lightning cursed the day I let it go
|
| posted on April 6th, 2004 at 07:16 AM |
|
|
Looks like it's going to be a racer with all the bar work
|
|
|
