| [ Total Views: 657 | Total Replies: 2 | Thread Id: 22111 ] |
|
|
 andrewh
Officially Full-On Dubber
Posts: 284
Threads: 24
Registered: January 20th, 2004
Member Is Offline
Location: Mountain View, CA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 25th, 2004 at 03:17 PM |
|
|
Seeking help removing old Beetle window scrapers
Hi all
I bought a new set of external window scrapers for my 74 Beetle a couple of weeks back and have only just got round to having a go at installing them.
Trouble is I can't for the life of me figure out how they're supposed to work. I've tried Googling and searching the forum but haven't come up
with any good clear guide on how to get them out.
Does anyone have any advice on how I might go about removing the old scraper + chrome without damaging the door, window or the rubbers. Hopefully once
I find out how to actually get them out it will become more obvious how the new ones go in.
Ta
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on April 25th, 2004 at 07:10 PM |
|
|
You have to drop the glass from the winder mechanism first. allow it to sit in the bottom of the door.
undo the rear lower baily channel next theres a screw in the door frame lower down.
remove the old baily channel felts from the rear of door and the top of door use a screw driver to leaver it out, i hope you bought new bailey
channels as well.
undo screw holding the 1/4 window frame in at the top it was under the bailey channel before then give the 1/4 window a shove back and down to
allow you to remove it.
now you should be able to use a paint scrapper to get between the inner scraper and the door to leaver it out and remove it.
do the same with the outer scraper but using yr fingers to push the trim clip out
sounds simple but take a lot of stuffing around
dont use the bailey channel clips to hold the outer trim in place use some self tappers and screw it down much better.
hope this helps
|
|
|
andrewh
Officially Full-On Dubber
Posts: 284
Threads: 24
Registered: January 20th, 2004
Member Is Offline
Location: Mountain View, CA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 25th, 2004 at 09:29 PM |
|
|
Excellent. Thanks a lot. That's exactly the sort of advice I was looking for.
Looks like I have some more bits to buy before I can go at it then.
|
|
|
Brad
Wolfsburg Elder
Posts: 3764
Threads: 332
Registered: August 24th, 2002
Member Is Offline
Location: SE QLD, Mt Nebo
Theme: UltimaBB Pro Blue ( Default )
Mood: Manx Buggy Building
|
| posted on April 25th, 2004 at 09:32 PM |
|
|
use a flat head screw driver wrapped in electrical tape not a paint scraper, this will let you work it harder before damaging any paint .
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on April 26th, 2004 at 08:45 AM |
|
|
After you have all the trim out of the way. Place a strip of masking tape along the top of the door next to window opening and mark a line where each
of the clip holes are on both outside and inside. this helps you when installing the new moldings.
The 1/4 window has to go in first. now is a good time to replace the rubbers on it as well.
Took me about 3 hours the other week to do a set for a friend.
Use plenty of masking tape around the window opening to protect the paint as well.
|
|
|
