| [ Total Views: 1506 | Total Replies: 11 | Thread Id: 23430 ] |
|
|
 fullnoise
Fahrvergnugen
Posts: 964
Threads: 103
Registered: September 21st, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Middle of the road.
|
| posted on May 25th, 2004 at 08:58 AM |
|
|
Another reason not to go for wide tyres on a beetle.
Some of you have probably heard me rattle on about choosing a thinner racing tyre so it will get up to operating temp.
Here's a reason for using a thinner tyre on the street too, especially on the front of your beetle.
By thin I'm suggesting using a 185 on a performance beetle rather than 205 wide tyre.
I copied this from The Tire Rack Website.
Aquaplaning or Hydroplaning.
Hydroplaning happens when one or more tires is lifted from the road by a wedge of water that gets trapped in front of and under a tire as the vehicle
drives through water. Hydroplaning most frequently occurs during heavy rainstorms when water creates puddles on the highway or expressway. In addition
to the accompanying splash and scaring the heck out of the driver, hydroplaning typically causes the steering wheel to jerk and the vehicle to
abruptly pull towards the puddle.
The speed at which a tire hydroplanes is a function of water depth, vehicle speed, vehicle weight, tire width, tread depth and tread design. It
depends on how much water has to be removed, how much weight is pressing down on the tires and how efficient the tread design is at evacuating water.
While deeper water, higher speeds, lighter vehicles, wider tires, less tread depth and less efficient tread designs will cause tires to hydroplane at
lower speeds; all tires will be forced to hydroplane at some speed.
As a rule, tread design affects hydroplaning resistance at high speeds and in deep water. Tread compound affects wet traction at lower speeds or in
shallow water.
CYA CT
esratrams
|
|
|
fullnoise
Fahrvergnugen
Posts: 964
Threads: 103
Registered: September 21st, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Middle of the road.
|
| posted on May 25th, 2004 at 08:59 AM |
|
|
If you want more grip get a better tyre not a wider one.
My 2 cents (rounded down). CT
esratrams
|
|
|
Keith Haeusler
Seriously Crusin Dubber
Posts: 168
Threads: 40
Registered: September 5th, 2002
Member Is Offline
Location: Picton , NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 25th, 2004 at 08:15 PM |
|
|
CT,
I have to agree with you there. Had exactly what the quote in your post says happen. Was travelling along the F3 with Hamo in his bug more or
less at the speed limit ( 70mph ) when the steering wheel suddenly jerked in his hands. You felt the front of the bug lift up, the tyre noise went
away and we just floated uncontrollably down the freeway. Anyway ended up crossing lanes as thats the way the water was flowing across the road
diagonally over say 100metres. Then the front came back down and away we went again. It scared the bejesus outta Hamo and im sure i shat myself. I
thoroughly do not recommend it to anyone. Have Fun. Keith.
|
|
|
Alex Holzl
A.k.a.: Big Al
Custom Title Time!
2332cc of pure BALLZ!!
Posts: 1550
Threads: 85
Registered: January 20th, 2004
Member Is Offline
Location: sydney, concord/mortlake
Theme: UltimaBB Pro Blue ( Default )
Mood: The peoples car that is faster than other peoples!
|
| posted on May 25th, 2004 at 08:34 PM |
|
|
mmmmmmm  .... bugga thats never good... what width wheels were thay |
|
|
Keith Haeusler
Seriously Crusin Dubber
Posts: 168
Threads: 40
Registered: September 5th, 2002
Member Is Offline
Location: Picton , NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 26th, 2004 at 08:04 PM |
|
|
Hi,
That was with 195 or 205 60 series, not sure which one.
Keith.
|
|
|
Anthiron
A.k.a.: Nicko McKay
Compulsive Aussie Vee Dubber
The Baja Rejuvenation Begins
Posts: 4936
Threads: 310
Registered: October 1st, 2003
Member Is Offline
Location: Buderim QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Hell hath no fury like a womans scorn for sega.
|
| posted on May 26th, 2004 at 09:03 PM |
|
|
shite! ....my baja had 215s on the front before the accident and i am now putting 195s on the front to improve steering.....it has 235s on the back:o
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom
|
|
|
VWFOOL
Bishop of Volkswagenism
King for a day, Fool for a lifetime.
Posts: 3436
Threads: 572
Registered: September 3rd, 2002
Member Is Offline
Location: Newcastle - Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: inspired yet?
|
| posted on May 26th, 2004 at 09:13 PM |
|
|
i aquaplaned in a 85 ford fairlane at 80kmh into the oncoming lane of the hwy, scared the shit out of me definetly.
++++++++++++++++++++++++++++
One man's junk...
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 26th, 2004 at 09:41 PM |
|
|
with 4 1/2 deg neg camber I'm probably only running a foot print the size of a 185 
Good points CT.
So are you happy with your new tyres.
|
|
|
Oasis
Custom Title Time!
Going alone...
Posts: 1806
Threads: 77
Registered: July 5th, 2003
Member Is Offline
Location: Cammeray, Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Deep
|
| posted on May 27th, 2004 at 01:07 AM |
|
|
I aquaplaned in my old Datsun 1600 doing 60kph! 205s with not much tread. I did a 360 over the median strip on Mona Vale road in Sydney and went
backwards up someone's driveway. Didn't hit or damage anything, and drove off shaking like a leaf!!!
"Tell him 'We've already got one'"
|
|
|
fullnoise
Fahrvergnugen
Posts: 964
Threads: 103
Registered: September 21st, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Middle of the road.
|
| posted on May 27th, 2004 at 08:29 AM |
|
|
Tread depth is also a factor in aquaplaning. Anything beyond 80% worn does a couple of things. It will increase your wet braking distance and lower
the speed at which your car starts to aquaplane.
Craig, the new tyres are excellent. They're not slippery when cold. I tried to induce understeer on my outlap to heat them up but they just gripped.
They gripped so well the car was leaning more in corners and heating up the outside edge or the outside tyres, even with 2.5 neg camber. The trouble
is the extra body roll was causing more inside rear wheel spin than ever before. I tightened the rear bar all the way and it reduced the wheelspin.
But I seriously need to tune that our or get a limited slip diff. Perhaps a bit more front swaybar and I'll put the stiffeners back on.
CYA CT
NB a bit more tyre pressure in wet conditions can open the grooves in the tread a little as well as putting more pressure on the middle of the tread
contact patch which helps water get pumped out the sides.
Low tyre pressures are really bad in the wet. The pressure is put on the sidewalls and the water is trapped under the centre of the tread. The also
lowers the speed at which your car will start to aquaplane.
esratrams
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 27th, 2004 at 03:21 PM |
|
|
good to hear CT
Interesting to note that you are now putting back the suspension products you removed, its amazing what a good set of tyres can do for your car
Your lap times will now get even better, leave the engine alone and now start playing with the gearbox. Fine tune your ratio's and maybe invest in a
Quaife or LSD.
Cheers
Craig T
|
|
|
fullnoise
Fahrvergnugen
Posts: 964
Threads: 103
Registered: September 21st, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Middle of the road.
|
| posted on May 28th, 2004 at 07:58 AM |
|
|
Hi Craig,
I don't know if the stiffeners work or not. I removed them after talking to someone who said the stiffeners caused his car's body to crack where
they bolt on. At the time my front suspension was very hard due to the adjustable front bar not working properly. I could easily imagine the shock the
beam was transmitting to the body. Now I've softened my front suspension and got rid of the understeer it's a good opportunity to see if the
stiffeners do anything. I will bolt them on between runs at wakefield park and rate them by the seat of my pants.
Have you done a back to back test with and without the stiffeners?
Have you done a back to back test with a stock-type whiteline bar vs and adjustable bar?
With regards to gear ratios that's where I draw the line. Gearboxes are big money and I'm not that serious about racing. Besides Jak and I have the
same boxes and that makes racing eachother more fun. I have another one of those boxes that I'm going to give to Paul so he can join in.
CYA CT
esratrams
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 31st, 2004 at 12:14 PM |
|
|
| Quote: | Originally
posted by fullnoise
Have you done a back to back test with and without the stiffeners?
Yes, I prefered the stiffeners.
Have you done a back to back test with a stock-type whiteline bar vs and adjustable bar?
I went from K-Mac bars straight to the Whiteline Adjustables, once I set the car up I have never needed to adjust. I adjusted them when I
went from an open diff to a Quaife
The only reason I changed from the KMac bar was due to the tyre hitting on the front mounts.
CYA CT
|
|
|
|
fullnoise
Fahrvergnugen
Posts: 964
Threads: 103
Registered: September 21st, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Middle of the road.
|
| posted on June 1st, 2004 at 08:18 AM |
|
|
Back to the topic.
Wheel and tyre weight is another good reason not to go too wide. Weigh a standard tyre and rim then weigh your combination. Imagine how much extra
strain you're putting on components like bearings and suspension joints.
Consider too that the suspension travel is less and the loads are increased due to more speed and more grip and bigger brakes.
Also another performance objective is to reduce the unsprung weight. I saved almost 2 kilos per wheel by changing from my last set of tyres to my new
set.
While you've got the scales out weigh a Porsche cookie cutter then weigh a contemporary after-market alloy.
Back to Craig.
It's interesting that your tyres rubbed the sway bar. Mine rub the shock and shock tower unless I adjust out the steering stops. I guess that's the
difference between running 14 inch and 16 inch rims.
You seem to have lots of steering lock available. How did you achieve that? The spacers I have between my hubs and wheels helped my steering lock but
I still can't do a U-turn on a regular street.
CYA CT
esratrams
|
|
|
