| [ Total Views: 459 | Total Replies: 6 | Thread Id: 31680 ] |
|
|
 warb
Custom Title Time!
gimme some butter im on a roll.....
Posts: 1982
Threads: 118
Registered: May 6th, 2003
Member Is Offline
Location: ya mummas house.
Theme: UltimaBB Pro Blue ( Default )
Mood: ORR50M
|
| posted on November 16th, 2004 at 06:22 PM |
|
|
starter..
stupid question for the day....
i have 2 starters here, i know they did work... i hook the battery up, (to both positive's) & earth with the neg, they just throw out the teeth,
they dont spin, first with the 6v battery, then them kicked them in the arse with the 12 volt... just throw the teeth out (a little quicker with the
12v  ) .. what am i missing here, i know they both worked... :duh
|
|
|
ancientbugger
Custom Title Time!
Posts: 1986
Threads: 191
Registered: March 24th, 2004
Member Is Offline
Location: sunshine coast
Theme: UltimaBB Pro Yellow
|
| posted on November 16th, 2004 at 07:43 PM |
|
|
They won't spin unless they're sitting in place as the bearing for the shaft end is in the gearbox bell housing that's why in your workshop manual
it tells you that they can't be bench tested.
|
|
|
warb
Custom Title Time!
gimme some butter im on a roll.....
Posts: 1982
Threads: 118
Registered: May 6th, 2003
Member Is Offline
Location: ya mummas house.
Theme: UltimaBB Pro Blue ( Default )
Mood: ORR50M
|
| posted on November 16th, 2004 at 08:31 PM |
|
|
ok, thanks, why wont it kick while installed.. it just throws the teeth (well thats what it sounds like) ... i will put the second one in tomorrow and
see that happens..
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on November 17th, 2004 at 06:25 AM |
|
|
make sure You grease the bush that the end of the starter motor shaft fits into....
You could have damaged the starters trying to get them to work without any support on One end....
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
warb
Custom Title Time!
gimme some butter im on a roll.....
Posts: 1982
Threads: 118
Registered: May 6th, 2003
Member Is Offline
Location: ya mummas house.
Theme: UltimaBB Pro Blue ( Default )
Mood: ORR50M
|
| posted on November 17th, 2004 at 07:05 AM |
|
|
well, i will find out this avo..
|
|
|
phatrat
A.k.a.: steve
Fahrvergnugen
REALLY!
Posts: 891
Threads: 107
Registered: May 14th, 2004
Member Is Offline
Location: Blue Mountains (NSW)
Theme: UltimaBB Pro Blue ( Default )
Mood: Buggin Out
|
| posted on November 17th, 2004 at 02:33 PM |
|
|
| Quote: | Originally
posted by ancientbugger
They won't spin unless they're sitting in place as the bearing for the shaft end is in the gearbox bell housing that's why in your workshop manual
it tells you that they can't be bench tested.
|
mmmm
|
|
|
phatrat
A.k.a.: steve
Fahrvergnugen
REALLY!
Posts: 891
Threads: 107
Registered: May 14th, 2004
Member Is Offline
Location: Blue Mountains (NSW)
Theme: UltimaBB Pro Blue ( Default )
Mood: Buggin Out
|
| posted on November 17th, 2004 at 04:47 PM |
|
|
| Quote: | Originally
posted by green57
well, i will find out this avo..
|
ya home?
|
|
|
