| [ Total Views: 700 | Total Replies: 4 | Thread Id: 3589 ] |
|
|
 Listy
Slammed & Awesome Dubber
Posts: 85
Threads: 30
Registered: January 3rd, 2003
Member Is Offline
Location: Banksia Park, SA
Theme: UltimaBB Pro Blue ( Default )
Mood: go Kombi go!!!
|
| posted on February 6th, 2003 at 09:25 PM |
|
|
bearings
Took the kombi to a tyre place today to check out the 'wobble' I feel at very slow speeds. He replaced the retread I bougtht off him a few
eeks ago as he said there was a flat spot where the join on the tyre is. While he was at it he mentioned that my front bearings needed re-doing. says
there's 'play' in each wheel...when you wiggle them, etc..
reckons he can do them for $45 a wheel. Question......is it easy to do myself (one of the reasons I bought a VW was to fix things myself). I have a
manual on the kombi, but the exploded view of the wheel assembly only shows a very small 'bearing race'. ? does this need replacing or
repacking. can someone be a daaaaaaarlingk and talk me through this step by step. layman's lingo perleez! 
Thanks in advance, ian
(@\|/@) (.\~/.)
|
|
|
Buggy Boyz
Posts:
Threads:
Registered: January 1st, 1970
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 6th, 2003 at 10:14 PM |
|
|
yep
It is very easy.
By bearings
Remove wheel
Remove dust cp
Unbolt Disc calliper
Undo axle nut
remove disc
Drift out old bearings and seals
Drift in new ones
Grease after and before assembly
Put it back on
Tighten nut then back of 1/2 turn
spin disc a few times, play with nut tension till there is no slope but no real resitance.
Put calliper back on
Put wheel back on
Go for drive
Jackup and check tension
Check again after 500km |
|
|
Buggy Boyz
Posts:
Threads:
Registered: January 1st, 1970
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 6th, 2003 at 10:16 PM |
|
|
oops
teach me to type and spell  |
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2818
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on February 7th, 2003 at 12:36 AM |
|
|
Depending on the condition of the bearings, they may just need adjusting. Just remove the dust cap and tighten the nut as per Brad's advice.
As a rough check, with the wheel jacked up, give it a spin and have a close listen for and rough spots while it turns, if there is any replace the
bearings. Otherwise pull them off and inspect visually.
|
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
| posted on February 7th, 2003 at 06:24 AM |
|
|
On the other hand, $45 a side isn't bad. I was quoted $170 for both sides, including parts.
Kruizin Kol
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on February 7th, 2003 at 06:28 AM |
|
|
Geezzz the bearings and seals are around 30 or so dollars. Make sure you watch him and he uses the new bearings. Instead of just tightening them up.
|
|
|
Baja Wes
Bishop of Volkswagenism
V6 Baja Pioneer
Posts: 3119
Threads: 94
Registered: August 26th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Content
|
| posted on February 7th, 2003 at 09:24 PM |
|
|
yeah $45 is cheap, parts are around $30 a side. I think he is quoting just tightening the spindle nut.
Jack the front of your car up so the front wheels are in the air. Wriggle the wheel in a vertical sense, in and out top and bottom. You will feel play
if there is any. Look carefully at what moves and make sure it is the bearing moving and not your ball joints or something.
Spin the front wheel. If it is relatively quiet the bearings should be OK. If it has a rumble than the bearings are stuffed. You can hear the rumble
when driving if they are stuffed.
If they are ok, tighten the spindle nut until you only just take out the play in the bearing. don't do it up with any force or you will crush the
bearing / make it wear out prematurely. Remember to do up the spindle nut locking mechanism.
|
|
|
Listy
Slammed & Awesome Dubber
Posts: 85
Threads: 30
Registered: January 3rd, 2003
Member Is Offline
Location: Banksia Park, SA
Theme: UltimaBB Pro Blue ( Default )
Mood: go Kombi go!!!
|
| posted on February 7th, 2003 at 11:06 PM |
|
|
thanks
thanks everyone. great stuff. I really appreciate the effort everyone makes here on this forum. OK, I took the wheel off and tried to tighten the nut,
but couldn't. I then contacted a mechanic friend who had a look and said there was nothing wrong with the bearings. there was a touch of play,
but he said that was ok as it was so slight. He did notice that my front brake pads were worn and the discs need to be machined! Thus the pulsating
feel (and maybe wobble?). getting it done monday. $45 for machining both wheels and $40 for the pads.
Cheers, ian
(@\|/@) (.\~/.)
|
|
|
SKEWtYpe3
Custom Title Time!
Posts: 1859
Threads: 107
Registered: August 26th, 2002
Member Is Offline
Location: Vic
Theme: UltimaBB Pro Blue ( Default )
Mood: Stiring The Pot
|
| posted on February 8th, 2003 at 01:48 AM |
|
|
pulsating and puling to one side is the feeling i got when my discs needed machining
:bounce
|
|
|
