| [ Total Views: 1127 | Total Replies: 8 | Thread Id: 70445 ] |
|
|
 satori
Wolfsburg Wizard
Posts: 497
Threads: 243
Registered: May 9th, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Grey
|
| posted on July 14th, 2008 at 09:21 PM |
|
|
Sanding and preping advice
I have been sanding back the paint on my wagen, which has a thick layer of white enamal on top of the last spray job.
I started using 180 grit wet and dry and has been taking alot to get it back. Is it ok to go down to
150 or even 120 to make it faster and then hit it with 240 to smooth it out?
thanks
[URL=http://s1226
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on July 14th, 2008 at 10:30 PM |
|
|
Paint stripper back to bare metal would be the only real way to go. Leaving any previous substrates could be the biggest mistake you will make.
Incompatibility between products will be your downfall. Consult your paint supplier.
|
|
|
satori
Wolfsburg Wizard
Posts: 497
Threads: 243
Registered: May 9th, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Grey
|
| posted on July 15th, 2008 at 10:50 AM |
|
|
Yeah right. I was reading about the strip it disks. They sound the way to go. I tried some paint striper on the bonnet to see how it would go and
found that it was all over the shot. one patch went right back, next to it only took off the top layer and so on.
[URL=http://s1226
|
|
|
rob53
Officially Full-On Dubber
Posts: 385
Threads: 62
Registered: January 19th, 2007
Member Is Offline
Location: Campbelltown
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 25th, 2008 at 08:57 PM |
|
|
If you put paint stripper and cover it with cling wrap and leave it for a while, you will get rid of most paint. A metal scrapper also helps.
I was also told that getting proper paint stripper from paint/panel beating suppliers makes a huge difference. (Admittingly, I have only use the
proper trade stuff)
The strip it disks can get pretty expensive unless you find some cheaper generic ones.
Thats not rust, it's ah ... orange primer ... yep that's what it is ...
|
|
|
Flat4Freak
A.k.a.: Steven
Casual Dubber
Posts: 38
Threads: 13
Registered: December 13th, 2006
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 15th, 2008 at 03:49 PM |
|
|
How messy can paint stripper get? I am looking to do most of the prep on my 68 beetle project myself and am worried about leaving a mess all over the
driveway of my unit.
|
|
|
helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on August 15th, 2008 at 06:01 PM |
|
|
If you are careful, it is only as messy as you are.
|
|
|
ozjeff
Learner Dubber
Posts: 19
Threads: 4
Registered: August 10th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 15th, 2008 at 11:32 PM |
|
|
you could get away with 2-3 strip it discs on a beetle, paint stripper isnt messy at all, just have plastic bags ready. Scrap off straight into the
bag.
|
|
|
Notch Nut
Custom Title Time!
Posts: 1011
Threads: 37
Registered: April 26th, 2006
Member Is Offline
Location: unknown
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 16th, 2008 at 10:24 PM |
|
|
What is the best surface prep after the paint stripper to avoid the etch primer reacting to the paint stripper?
If you can't fix it with a hammer,
you have an electrical problem....
|
|
|
trickysimon
A.k.a.: Simon Azzopardi
Custom Title Time!
100km/h is only 9 seconds away
Posts: 1473
Threads: 43
Registered: December 15th, 2007
Member Is Offline
Location: Wagga Wagga
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 17th, 2008 at 01:33 AM |
|
|
At TAFE we just wipe it over with a wet rag then when its dry clean with wax and grease remover. Well at least I think we do (Too much Vodka, sorry it
aint no rum  )
Simon
|
|
|
