| [ Total Views: 1012 | Total Replies: 10 | Thread Id: 74916 ] |
|
|
 telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 23rd, 2009 at 01:50 PM |
|
|
Type 3 Beam Bearing
Dose any 1 know if its easy or has any 1 ever replaced a bearing or the inner bush on a type 3 beam
ive finaly found a bush & bearing but ive asked a few places about it but no 1 has ever replaced 1. So at the mo im on my own
would replace the beam bu cant find 1
Thanks For the help
Telf
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on February 23rd, 2009 at 03:48 PM |
|
|
you will need the special tool talk with Vintage in Sydney 02-9789-1777
|
|
|
telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 23rd, 2009 at 04:22 PM |
|
|
is the tool to pull out the bearing or the bush
|
|
|
type3lover
A.k.a.: The Smashed Repairer
Insano Dub Head
in the garage...
Posts: 796
Threads: 90
Registered: February 2nd, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
Mood: stoked
|
| posted on February 23rd, 2009 at 06:35 PM |
|
|
Hey Telf what parts are needed and where did you get them?
I need to do mine too as one looks to be cracked...bump!
.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on February 23rd, 2009 at 07:19 PM |
|
|
both
|
|
|
telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 24th, 2009 at 08:42 AM |
|
|
So is it a bearing puller.
There are 2 places ive found them ISP West in the US & T3D in the uk. I think im only looking at getting the bearing. make sure you stat either
top or bottom as they are different sizes.
Why do yo think you need a new 1 what happens.
mine has a really bad wobble in the stearing wheel when i go over bump
i jacked it up and the pasenger side was all spongy when you turned it quickley.
Hope this make sence.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on February 24th, 2009 at 08:46 AM |
|
|
have you tightened the sway bar / torsion bar up
pretty sure theres a bolt on the pas side between the arms it needs to betight
check on the drive side if not on pass side
|
|
|
telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 24th, 2009 at 09:48 AM |
|
|
was the first thing i did and no change unfortunatly.
after it being lowered 3 outer spline for a few years now im sure that that would take its toll on the old bearings.
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on February 24th, 2009 at 03:53 PM |
|
|
R/H/S dave,they used to have a lock tab but most of these are gone now.loosen the lock bolt on the bar,and tighten the adjustment bolt,lock the lock
bolt again.(been a lot of years since this was a daily chore)
|
|
|
telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 6th, 2009 at 04:28 PM |
|
|
New Question dose any 1 know of any 1 selling a type 3 beam
think i might take a new direction
preferably near the gold coast direction
|
|
|
telf
Officially Full-On Dubber
Posts: 207
Threads: 53
Registered: January 10th, 2007
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 20th, 2009 at 01:07 PM |
|
|
All sorted got a new beam, going on this weekend thanks for all your help
Telf
|
|
|
