| [ Total Views: 733 | Total Replies: 3 | Thread Id: 7589 ] |
|
|
 pavelmac
Casual Dubber
Posts: 30
Threads: 11
Registered: May 2nd, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2003 at 10:13 AM |
|
|
Kombi fuel guage
Hi,
Can anyone tell me if the fuel gauge from a '76 T2 is compatible with my '71/'72 T2? Only I have just swapped my old dash (in MPH) for
a '76 one (in KPH) and all is fine but for the fuel gauge needle disappearing off past full! I've tried to swap back to the original dash
but I get the same result. So I don't know whether to conclude that I have got the wrong wires or I've buggered up the sender.
The dash differs mainly by the '76 version having a silver box that appears to connect to the fuel sender & and a few less bulbs (only 1
indicator bulb & no low beam bulb).
Any ideas?
|
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
| posted on June 18th, 2003 at 06:34 PM |
|
|
Maybe you need to use the matching sender? :o
My kombi's both had the opposite problem: even when full to overflowing, they still only registered between 1/2 and 3/4 of a tank. At least
I've never ran out of petrol though, I always have at least 1/4 of a tank as reserve!!! :thumb
Kruizin Kol
|
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2818
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on June 18th, 2003 at 09:05 PM |
|
|
Does sound like something incorrectly wired if putting the old gauge gives the same incorrect result.
I'm planning to do the opposite in the near future, (swap new dash for old) so I will keep you posted. (Don't hold your breath though).
Andy
|
|
|
koolkarmakombi
Veteran Volks Folk
enkarmarising
Posts: 2078
Threads: 158
Registered: June 16th, 2003
Member Is Offline
Location: viva brisvegas
Theme: UltimaBB Pro Blue ( Default )
Mood: do you see the bats?
|
| posted on June 23rd, 2003 at 02:28 PM |
|
|
I have a new 73-80 sender in my hands as I write. If you look on the back of the fuel guage, they use a different gizmo to 'damp' the
circuit- or so im told. If you use same year sender/guage it should work. Check the earth lead for the tank. On my '75 in screws to the top
bulkhead above the tank and in my case was not earthing- more like mooning 
Wire the sender directly to the guage and see if it all works without the kombi wiring being involved. If it all works then, wires are shot.
A big shout out to Andy in thanks for the piccy before I went a drilling.:beer your way fella
toddly |
|
|
kombikim
A.k.a.: Kim
Custom Title Time!
disfunctionally capable
Posts: 1521
Threads: 84
Registered: December 18th, 2002
Member Is Offline
Location: Sydney, Concord West
Theme: UltimaBB Pro Blue ( Default )
Mood: always bleary
|
| posted on June 23rd, 2003 at 05:34 PM |
|
|
on the back of the instrument panel is a little rectangular box with a couple of terminals of which one wire goes to the fuel gauge (simplifing it a
bit) it stabilises the voltage at about 8volts or thereabouts so that the guage gives a staedy reading no matter what output is coming from the
alternator or battery.
because both the panels are now reading full, it seems like you have bypassed the voltage stabiliser & hitting the gauge with the full 12 to 14
volts |
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2818
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on June 23rd, 2003 at 10:04 PM |
|
|
Any time Toddly,
Just hope you didn't drill into the tank 
|
|
|
