| [ Total Views: 1514 | Total Replies: 6 | Thread Id: 78091 ] |
|
|
 dubless
Learner Dubber
Posts: 5
Threads: 2
Registered: February 18th, 2009
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Grumpy
|
| posted on July 29th, 2009 at 10:19 PM |
|
|
91 Caravelle Conversion advice
Hello,
Looking to convert my 91 caravelle to an EJ25. Mechanically challenged and will need to have this done professionally. Anyone suggest a good mechanic
in Sydney that will do this properly?
Thanks in advance
M |
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 31st, 2009 at 08:06 PM |
|
|
not in NSW , but in QLD you will find AM AUTO , AL , I dont think you will find any one out there better IMO
Looking for that special lady : PM me for coffee & cake
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on August 3rd, 2009 at 11:33 AM |
|
|
Quikfit motorsport at Hornsby or Indian Automotive at Kingswood. They've both done heaps of these conversions.
|
|
|
satori
Wolfsburg Wizard
Posts: 497
Threads: 243
Registered: May 9th, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Grey
|
| posted on September 14th, 2009 at 10:44 PM |
|
|
Be prepared to pay top dollar when getting it professionally done. Easily over $10,000. I just finished my 86 caravelle conversion and can understand
why it cost so much, a shit load of work to do yourself. Cost me just under $4000, the engine cost me $1200 but only had 140,000 km on it and had been
fully servied.
[URL=http://s1226
|
|
|
ericos_bob
Learner Dubber
Posts: 16
Threads: 4
Registered: November 16th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 6th, 2009 at 02:51 PM |
|
|
What did you find most difficult during your conversion and how long did it take you to do. I thought the wiring loom would be most time consuming?
Did you have problems getting your conversion approved. This is my biggest concern doing a home conversion. cheers
|
|
|
Transparu
Seriously Crusin Dubber
Posts: 154
Threads: 79
Registered: February 19th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: GREAT!!
|
| posted on October 7th, 2009 at 07:33 AM |
|
|
I put in an EJ22 7 years ago - and am still very happy. Whilst I didn't do it, the making and welding of engine supports and the exhaust would be
the greatest task. The wiring loom, whilst consuming quite a lot of time and attention, wasn't hard at all. It IS important to start with (a) the
loom from YOUR engine, and (b) some sort of diagram/instructions for the wiring. You will also be well served with a large desk (or, better, a spare
door to put on a desk as a work surface.) You could always do this as an evening job. 2-3 hrs at a time is ample, as long as you can tell one colour
from another and are methodical.
There is loads of info available on the Yahoo subaruvanagon website.
Approval in QLd was fine (though the guy knew and trusted the work of the people who did the welding work). Make sure there are anti-crush spacers in
the chassis members where the new engine mount bolts on.
All the best.
Dave
| Quote: | Originally
posted by ericos_bob
What did you find most difficult during your conversion and how long did it take you to do. I thought the wiring loom would be most time consuming?
Did you have problems getting your conversion approved. This is my biggest concern doing a home conversion. cheers
|
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 7th, 2009 at 06:35 PM |
|
|
send you loom to Al @ AM Auto as I do with mine
Looking for that special lady : PM me for coffee & cake
|
|
|
