| [ Total Views: 1960 | Total Replies: 5 | Thread Id: 78135 ] |
|
|
 djnee
Officially Full-On Dubber
Posts: 341
Threads: 59
Registered: March 23rd, 2009
Member Is Offline
Location: Lara, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: going lower...
|
| posted on August 1st, 2009 at 08:39 PM |
|
|
Running cables through heater channels?
As my heater channels are no longer connected to heat, i was thinking of running the cables for my audio install through them.
Just wondering if anyones done this before?
Ideally i would like to run something like hosepipe as a conduit from the front of the car (at the top of the A panels under the bonnet) and have it
exiting through the rear heater port under the back seat near the battery.
Not sure how much room there is at the bottom of the A panel bit though...as it's obviously got to do a 90 degree there. Is there enough room?
If this is a definate no-go then does anyone have any other ideas for running cables from front to rear without doing the normal under the carpet job?
Thanks
Neil
Hi Neil,
I ran some cables thru the centre section of the chassis.
the cable went in near where the fuel goes into the tunnel.. it comes out under a rear seat....
the cable was 7 core trailor cable..
cheers
LEE
|
|
|
Brad
Wolfsburg Elder
Posts: 3764
Threads: 332
Registered: August 24th, 2002
Member Is Offline
Location: SE QLD, Mt Nebo
Theme: UltimaBB Pro Blue ( Default )
Mood: Manx Buggy Building
|
| posted on August 1st, 2009 at 11:03 PM |
|
|
Going through the heater channel is fine. Just put the hose down first and then cable through that. The channel is not hollow as such but the old
heating pipe will allow you to avoid the obstacles.
From VWDrives Website - http://www.vwdcqinc.org.au/vwdcqimages/insideabugimages/heaterchannel.html
|
|
|
eraser
Fahrvergnugen
Posts: 970
Threads: 128
Registered: March 11th, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Powder
|
| posted on August 2nd, 2009 at 09:24 AM |
|
|
what a great shot  thx for finding and linking.. i know know whats in the
heater channels
|
|
|
djnee
Officially Full-On Dubber
Posts: 341
Threads: 59
Registered: March 23rd, 2009
Member Is Offline
Location: Lara, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: going lower...
|
| posted on August 5th, 2009 at 01:24 PM |
|
|
Just to report....
Can't seem to get past the 90 degreee at the bottom of the A pillar.
Back to zee drawing board....
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on August 5th, 2009 at 01:31 PM |
|
|
can ya pre kink an angle into the hose a bit and then by shovin in it will direct itself?? with the walls of the heater channel?
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
Old Dubber
Wolfsburg Wizard
Posts: 605
Threads: 25
Registered: August 26th, 2002
Member Is Offline
Location: Everton Hills, Brisbane, QLD, Australia 4053
Theme: UltimaBB Pro Blue ( Default )
Mood: great!
|
| posted on August 5th, 2009 at 06:37 PM |
|
|
Neil,
Try something more flexible first, like an accelerator/clutch cable
first and then use this as a drawstring for your hose.
Grahame
|
|
|
