| [ Total Views: 591 | Total Replies: 5 | Thread Id: 7854 ] |
|
|
 lugnuts
A.k.a.: Mike
Custom Title Time!
Posts: 1070
Threads: 88
Registered: August 28th, 2002
Member Is Offline
Location: Sydney,Castle Hill
Theme: UltimaBB Pro Blue ( Default )
Mood: semi-retiring
|
| posted on June 26th, 2003 at 02:53 AM |
|
|
Line Boring
Hiya,anybody know how many times you can linebore a T1 case and the last size especially,i just measured mine at 66.5mm,oh and only tell me if its
good news |
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2003 at 08:28 AM |
|
|
I "thought" they were suppose to stamp what size they bore to on the inside??
I have heard of people boring to 60 thou (1 1/2mm :o ) but if it is for a hottie i wouldnt go past 10 thou.
No expert but i would be more worried about the thrust cut on the face. I think there is more hammering there from the back and forth rather than the
flexing/harmonic of the crank
Futue te ipsum!!!
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 26th, 2003 at 08:53 AM |
|
|
there are only 4 oversize back bearings available
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2003 at 09:28 AM |
|
|
true - 10,20,30 and 40 thou.
I have "heard" a few of the GEX's and the like use to 60 thou - dont know where they get bearings from
Futue te ipsum!!!
|
|
|
lugnuts
A.k.a.: Mike
Custom Title Time!
Posts: 1070
Threads: 88
Registered: August 28th, 2002
Member Is Offline
Location: Sydney,Castle Hill
Theme: UltimaBB Pro Blue ( Default )
Mood: semi-retiring
|
| posted on June 26th, 2003 at 04:13 PM |
|
|
Thanks guys yeah the bearing had something written on it ile see if i can decipher it:thumb |
|
|
lugnuts
A.k.a.: Mike
Custom Title Time!
Posts: 1070
Threads: 88
Registered: August 28th, 2002
Member Is Offline
Location: Sydney,Castle Hill
Theme: UltimaBB Pro Blue ( Default )
Mood: semi-retiring
|
| posted on June 27th, 2003 at 05:01 PM |
|
|
Ok,this is on one of the bearings 2931 AIO72+1,50-STD on the outside and Fm L on the inside,this bearing is the big one on the end.This one is
the little one on the other end of crank 2933 AT+1,50-STD BRAZIL.So sounds like this case is know a large doorstop,might get it ceramic coated as an
experiment. |
|
|
lugnuts
A.k.a.: Mike
Custom Title Time!
Posts: 1070
Threads: 88
Registered: August 28th, 2002
Member Is Offline
Location: Sydney,Castle Hill
Theme: UltimaBB Pro Blue ( Default )
Mood: semi-retiring
|
| posted on June 27th, 2003 at 05:15 PM |
|
|
[Edited on 27-6-2003 by lugnuts] |
|
|
Che Castro
Custom Title Time!
ankle straps
Posts: 1945
Threads: 79
Registered: August 25th, 2002
Member Is Offline
Location: Sydney, Australia
Theme: UltimaBB Pro Blue ( Default )
Mood: (( }:-{D]
|
| posted on June 28th, 2003 at 01:33 PM |
|
|
if ur going for a hottie just get a good std/std used one, or a new case. its better in the long run i reckon
Jon
|
|
|
