| [ Total Views: 1253 | Total Replies: 27 | Thread Id: 80805 ] |
|
|
 Yogie
Super Moderator
Posts: 1603
Threads: 108
Registered: June 7th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
|
| posted on December 13th, 2009 at 07:30 PM |
|
|
Take off the hubcap and the cable sticks out through the dust cover. You will have to push off the circlip that holds the cable in place. After you
do that, the cable can be slid out of the cover.
Yogie
|
|
|
 amazeer
A.k.a.: Surly Duff
Bishop of Volkswagenism
Posts: 3029
Threads: 387
Registered: November 14th, 2005
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: bitter
|
| posted on December 13th, 2009 at 08:03 PM |
|
|
if "everything else works on it except the km/h dial" includes the mileage is still ticking over then you dont have a problem with the cable. If the
needle and the odometer arent working then it could be either the cable or speedo. The speedo is just a holder for the lights, so they arent really an
indication of its functioning. Usually speedo problems are with the cable though.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on December 13th, 2009 at 09:03 PM |
|
|
| Quote: | Originally
posted by Abp66
Ok so my speedo stopped working again today...
i know its not the speedo because it was working before fine and everything else works on it except the km/h dial
im sure its the speedo cable so i unscrewed the cable from the back of the speedo. and the inside of the cable was loose (im not sure if it is meant
to be like that?) and jacked my car up and had a look under the wheel and it was intact there. can some one tell me how to take the cable out of the
left hand wheel and see if the cable is broken?
thanks guys 
|
Hi
You need to pull the LH front hubcap off...
then knock or pull the small circlip off and pull the cable from behind the axle etc...
the inner speedo cable is sort of loose all the time.. but You shouldn't be able to twist it around with the wheel on the ground... with the wheel
off the ground, spinning the wheel will turn the inner cable..
Just because the speedo did work last time, doesn't mean it will work next time.. the cable can break at any time..
the circlip may have come off the cable...
BUT- usually the cable snaps off slowly which will make the needle jump up & down before it snaps off completely..
Cables are very inexpensive... I always pour a few drops of oil down from the top to lubricate the cable..
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 13th, 2009 at 10:53 PM |
|
|
Sometimes the square drive hole in the bearing dust cover gets worn and looses grip of the cable. Can be repaired by peening, welding or replacing.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
amazeer
A.k.a.: Surly Duff
Bishop of Volkswagenism
Posts: 3029
Threads: 387
Registered: November 14th, 2005
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: bitter
|
| posted on December 14th, 2009 at 07:26 PM |
|
|
when you get the new cable attach it to the speedo without threading it through the body first. If you cant turn the wheel end freely without any
resistance you probably also have a problem with the speedo.. which could be the cause of the cable breaking. probably not an issue but you dont want
to go breaking another cable to find out.
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on December 3rd, 2010 at 08:53 AM |
|
|
Did a search to find this, my problem is the speedo stoped working kinda sudden like and now I get a realy loud scraping screeching sound which sounds
like the cable is grinding away at something, possibly the outer cable, I have removed the dust cap thingie from the front wheel and undone the end
from the speedo but I can't draw the inner cable out of the outer from the wheel end, as it's a buggy I can't get at the speedo end well enough to
pull it out from that end. Also the dust cap at the wheel no longer has a square hole in it, seems to be flogged out and when I took the center cap
off the rim the dust cap was hanging loose. Am I supposed to be able to remove the inner cable from the outer from either end?
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on December 3rd, 2010 at 08:56 AM |
|
|
Hmm, seems a search found this in the wrong section, shoulda been in tech talk I think, maybe a mod can move it?
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on December 3rd, 2010 at 02:06 PM |
|
|
Hi Donn
I believe the inner can be taken out but haven't tried it..
I always buy the complete speedo cable which isn't expensive.
have two spares so don'/t need to buy another one..
I should replace mine as it sways when going slow...
I always oil the cable.. so it probably won't snap...
the cables are made from many pieces of spring steel so they don't snap cleanly...
I do remember seeing the cable end welded to the cap on a beetle.... not sure who's beetle.. lol
I remember many years ago, when the cable snapped, it did it slowly with the needle going everywhere... lol
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on December 3rd, 2010 at 02:30 PM |
|
|
Thanks Lee, my problem is that in the buggy the cable goes between the f/glass body and the steel bracing unit just behind the speedo and that dosn't
leave enough room to take the knurled nut out between them, only way I can see to remove the outer is to lift the body shell, trying to avoid that if
I can.
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on December 3rd, 2010 at 04:54 PM |
|
|
| Quote: | Originally
posted by donn
Thanks Lee,
my problem is that in the buggy the cable goes between the f/glass body and the steel bracing unit just behind the speedo and that doesn't leave
enough room to take the knurled nut out between them, only way I can see to remove the outer is to lift the body shell, trying to avoid that if I can.
|
YIKES...
that sounds bad...
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
amazeer
A.k.a.: Surly Duff
Bishop of Volkswagenism
Posts: 3029
Threads: 387
Registered: November 14th, 2005
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: bitter
|
| posted on December 3rd, 2010 at 09:22 PM |
|
|
Cut it dude, sidecutters are your friend
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on December 3rd, 2010 at 09:48 PM |
|
|
Will sidecutters help me get the new one back in?
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
amazeer
A.k.a.: Surly Duff
Bishop of Volkswagenism
Posts: 3029
Threads: 387
Registered: November 14th, 2005
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: bitter
|
| posted on December 3rd, 2010 at 09:55 PM |
|
|
No, but your not going to put the new cable in the same dumb place where it needs body removal are you? I'd be re-routing the cable.
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on December 4th, 2010 at 06:04 AM |
|
|
Subject: Speedo Problems!
Not knocking your help amazeer, I'll listen to any comments / suggestions (actualy I'll read em ) but in this case there is no option, the reinforcing bar is about 25mm behind the speedo and the top of the
bar is about 1.76589 mm below the bottom of the outer cable, I'm tempted to just put the tremendouse forces of my right arm and a pair of vice grips
to work and see if I can haul the cable out of the outer but I know that spells potential disaster
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 21st, 2012 at 04:19 PM |
|
|
So 7+ months down the track I'm back at it, as it turned out the square end on the cable was worn so I packed it out to a place that wasn't worn and
it did the trick till now, as expected the square end on the cable is now totaly round and wont grip in the square hole in the dust cap so I have no
choice but to replace the cable, I know that the cables arn't expensive but I cant get the outer out of the car (see previous posts above) so I have
to do only the inner, any clues on how to do this as the inner seems to be caught and I am having trouble removing it from the outer.
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
amazeer
A.k.a.: Surly Duff
Bishop of Volkswagenism
Posts: 3029
Threads: 387
Registered: November 14th, 2005
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: bitter
|
| posted on July 21st, 2012 at 09:04 PM |
|
|
would some araldite buy some more time?
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 22nd, 2012 at 11:22 AM |
|
|
| Quote: | Originally
posted by amazeer
would some araldite buy some more time?
|
Hmm, kinda doubt it, maybe a spot of weld but I reckon there's got to be a way, still working on it, BTW, what happened to the subject? all I've got
is a blank spot. 
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
h
A.k.a.: Towely BuMpEr KING! ILLegal ALIEN on a roadtrip
Scirocco Rare
fractals - an ever changing lifestyle
Posts: 7670
Threads: 375
Registered: February 3rd, 2005
Member Is Offline
Location: noosa hillbilly 'yee har'
Theme: XMBX Pro Green
Mood: A T3 is not a Kombi - stop waving at me
|
| posted on July 22nd, 2012 at 11:30 AM |
|
|
wow by the thread title I was expecting to see Officer Bar Brady with no pants on, arms in the air moving people along as there was nothing to see
here
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 22nd, 2012 at 11:35 AM |
|
|
Ha Ha, now it's got "pages 1,2" 
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 22nd, 2012 at 03:46 PM |
|
|
| Quote: | Originally
posted by donn
So 7+ months down the track I'm back at it, as it turned out the square end on the cable was worn so I packed it out to a place that wasn't worn and
it did the trick till now, as expected the square end on the cable is now totaly round and wont grip in the square hole in the dust cap so I have no
choice but to replace the cable, I know that the cables arn't expensive but I cant get the outer out of the car (see previous posts above) so I have
to do only the inner, any clues on how to do this as the inner seems to be caught and I am having trouble removing it from the outer.
|
From memory, I'm fairly sure the inner can only be removed from the speedo end. The inner should slide freely in and out, so if you can't gently
pull it through from the wheel end, that means it is not designed to come out that way.
|
|
|
Klaus
Custom Title Time!
Posts: 1439
Threads: 100
Registered: August 25th, 2004
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: Heavily modified
|
| posted on July 23rd, 2012 at 09:58 PM |
|
|
get a rhs cap drill a small hole then file a small square into it , then file the end of the rounded cable into a smaller square too and either small
split pin or "r" clip or circlip to hold it or file it off centre and weld fill half the old cap hole
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 24th, 2012 at 09:37 AM |
|
|
Thanks Klaus, that's what I had decided to do (sorta) but my friendly VW mechanic has given me another idea when I went down to see him, he sold me a
new cable with a "return if it dosn't work" tag, but for $28 it wouldn't be worth the trip, I'll let you know how it goes.
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 24th, 2012 at 05:23 PM |
|
|
Please delete all mention of how difficult this is, turned out to be easy as, I'm a dope.   
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on July 24th, 2012 at 06:00 PM |
|
|
After all this time of putting it off & looking for alternatives.................
From your ole' mate Jeff
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 25th, 2012 at 09:50 AM |
|
|
No need to rub it in Jeff 
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
