| [ Total Views: 1087 | Total Replies: 5 | Thread Id: 81758 ] |
|
|
 one4
Seriously Crusin Dubber
Posts: 130
Threads: 25
Registered: October 29th, 2005
Member Is Offline
Location: Alice Springs
Theme: UltimaBB Pro Blue ( Default )
Mood: Warm Summer Crusing
|
| posted on February 2nd, 2010 at 10:49 AM |
|
|
Engine firewall noise?
Hey guys,
I am in the process of finishing off the design for my firewall after I cut into it to fit the water to air intercooler. It's in a type 1/ beetle.
When discussing the final design with some friends they suggested that if I use flat metal at certain frequencies I may get a really bad vibration
noise through the metal.
I was wondering if other people had experienced any problems with this and whether I need to get metal bent to avoid this? Either get those pressed
hot rod style piece or something else?
One other thought, which I'm thinking is the easiest is the use of steel checkaplate. Just putting it out there for any thoughts or whether it is
really an issue or not.
Cheers
Richard
|
|
|
Sides
A.k.a.: Dave Sidery
Veteran Volks Folk
Posts: 2220
Threads: 59
Registered: May 20th, 2007
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
Mood: Need... more... shed... time...
|
| posted on February 2nd, 2010 at 02:59 PM |
|
|
Yeah, flat metal "drums" a lot easier than metal with bends or pressings in it.
Don't know that using checker would really solve it at all... normal solution with cars is to use decent sound deadening material, something along
the lines of Dynamat to add mass to the panel and so reduce the effect.
VWDCQ vice pres & web dude - vwdcqinc.org.au
Join a car club - get car peeps
My toys
'70 Hillclimb Bug 'Jezebel' w/- Haltech EFI - http://bit.ly/VwTNtQ
'60 KG Coupe - resto kinda started
01 New Beetle - gf's car, but I turn the spanners |
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on February 2nd, 2010 at 07:38 PM |
|
|
http://www.dci.com.au/services/thermal_acoustic_shielding
|
|
|
one4
Seriously Crusin Dubber
Posts: 130
Threads: 25
Registered: October 29th, 2005
Member Is Offline
Location: Alice Springs
Theme: UltimaBB Pro Blue ( Default )
Mood: Warm Summer Crusing
|
| posted on February 2nd, 2010 at 08:58 PM |
|
|
I was told because of the diagonal patten on the checkaplate it would stop the vibrations as much as the flat surface.
I will be using Dynamat sound proofing as well as their insulation kits as I can get them from work but just wondering whether I really need to worry
about using flat metal or should I really get stuff with bends pre made?
Cheers for your answers so far.
Richard
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on February 2nd, 2010 at 11:50 PM |
|
|
Hi
A good sheetie can put a diamond/X bend in a flat panel with a folder, that is like a shallow bend from corner to corner forming an X. The biggest
issue would be heat.
Steve
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on February 3rd, 2010 at 07:08 PM |
|
|
| Quote: | Originally
posted by 1303Steve
Hi
A good sheetie can put a diamond/X bend in a flat panel with a folder, that is like a shallow bend from corner to corner forming an X. The biggest
issue would be heat.
Steve
|
yeah why is it so hot when my turbo is glowing red
|
|
|
