| [ Total Views: 798 | Total Replies: 5 | Thread Id: 84193 ] |
|
|
 1500S
Custom Title Time!
Posts: 1418
Threads: 73
Registered: March 28th, 2005
Member Is Offline
Location: Nth Richmond, N.S.W
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 9th, 2010 at 08:52 PM |
|
|
Type 3 Drum Brake Cyls
As most would know, early Type 3 drum brake slave cylinders are getting hard to get. Some turn up NOS on Fleabay from time to time but can be
expensive. I got caught a bit, only because I treated early Type 3 as being all the same with the slaves, forgetting that pre 64 had different
diameter drums and shorter slaves. What to do?? Don't keep looking for NOS for the 64 and later as you'll waste a lot of time. Get them sleeved
with stainless steel back to new without the worry of the dreaded rust coming back. If you have a lathe and the knowhow it's not a great deal. 316
stainless being preferred for corrosion resistance making sure that the surface finish is nice and fine off the lathe before the final hone after
assembly. Use a proper interference fit rather than rely on some chemical fixing compound........... it's only used as an excuse for a poor
machinist!! 
A pic of one of the lefts before assembly of spring and cup.
DH
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on June 9th, 2010 at 09:13 PM |
|
|
nice work.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on June 9th, 2010 at 09:18 PM |
|
|
and you do this for entertainment Dallas..?? lol
My master cylinder was done and many others I know of...
they do motor cycle master cylinders too..
I never thought of brake cylinders.. but rare ones like yours...
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
1500S
Custom Title Time!
Posts: 1418
Threads: 73
Registered: March 28th, 2005
Member Is Offline
Location: Nth Richmond, N.S.W
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 9th, 2010 at 09:39 PM |
|
|
| Quote: | Originally
posted by 68AutoBug
and you do this for entertainment Dallas..?? lol
My master cylinder was done and many others I know of...
they do motor cycle master cylinders too..
I never thought of brake cylinders.. but rare ones like yours...
cheers
LEE
|
Little things like this is pure entertainment compared with some of the stuff I still do Lee! I was back at the old work for a couple of days last
week and it took more time to find the "flexhone" than do the actual sleeve! No! I didn't do any foreign orders there as there is generally too
much interference from bloody apprentices! The store is in a bit of a mess and things seem to be getting scattered by "the new bloke" who has no
interest in the section. After I get the both sides done the master cyl will most likely get the same treatment. I have a kit to put into it but
haven't taken it off yet to see what the inside's like. It was NOS back in '91 but the back seal is definitely weeping. Just not enough use over
the years.
DH
|
|
|
type3lover
A.k.a.: The Smashed Repairer
Insano Dub Head
in the garage...
Posts: 796
Threads: 90
Registered: February 2nd, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
Mood: stoked
|
| posted on June 9th, 2010 at 09:45 PM |
|
|
Good to see you found a solution!!
.
|
|
|
1500S
Custom Title Time!
Posts: 1418
Threads: 73
Registered: March 28th, 2005
Member Is Offline
Location: Nth Richmond, N.S.W
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 12th, 2010 at 12:48 PM |
|
|
| Quote: | Originally
posted by type3lover
Good to see you found a solution!!
|
Well not fully Toby! As you are aware, out west of Sydney and no doubt, many other areas, it's difficult to find parts for our old cars especially
if you want them to conform to near original.
After wasting time scratching through dust and grime in semi darkness at an outer west "repairers" as well as at the local Windsor Brake and Clutch
repairer, it was back to the home workshop where I should have stayed in the first place . 
The 46 year old bleeder nipple was showing it's age along with being partly rusted in on the thread so in less time than it took to drive to
Riverstone, I now have a couple of stainless steel bleeders to do the job. Sure looks better than the old one!
DH
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
