| [ Total Views: 699 | Total Replies: 5 | Thread Id: 86869 ] |
|
|
 OLLY
Slammed & Awesome Dubber
Posts: 78
Threads: 25
Registered: May 22nd, 2009
Member Is Offline
Location: coffs harbour
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 30th, 2010 at 07:30 PM |
|
|
fuel delivery pipe
would like some ideas on how to make sure the pipe that goes in to the carburettor doesn't make it's way lose.
thinking of tie wire around clamp then around carburettor
thanks
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 30th, 2010 at 07:32 PM |
|
|
| Quote: | Originally
posted by OLLY
would like some ideas on how to make sure the pipe that goes in to the carburettor doesn't make it's way lose.
thinking of tie wire around clamp then around carburettor
thanks
|
or wire clamp to closest screw as on aircraft..
also do the fuel pump...
as they can pop out too....
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on October 30th, 2010 at 10:45 PM |
|
|
Some people are now taping the inlet hole and fitting a fuel pipe fitting... so, it can't come out....
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 31st, 2010 at 04:44 AM |
|
|
I have been doing this for years you can also makea small metal tab with a hole in it to go under one of the carby top cover screws or wrap a
piece of tie wire aroun d the carby as you suggest
Also the most important one is to do the fuel pump outlet line as this will and does also fly off under pressure
the problem is you have 2 diffent metals brass and Alluminium so Corrosion can occur between the diferent metals and will cause the pipe to come off
and creat a fire
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on October 31st, 2010 at 08:05 AM |
|
|
Most people by now have one of the replacement pumps with the 1 piece pressed steel tops so they cant spit the fitting out.
As above the best saftey measure is the old saftey wire on the carb and old style pumps
|
|
|
OLLY
Slammed & Awesome Dubber
Posts: 78
Threads: 25
Registered: May 22nd, 2009
Member Is Offline
Location: coffs harbour
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 31st, 2010 at 03:06 PM |
|
|
Hi thanks for the idea's all have helped , I will look in to the tap and thread later but for now I used a ring terminal Dia:4.3mm which the carb
screw went threw. threaded the wire threw and crimped the end .little twist end bit of wire and done.
olly
|
|
|
