Board Logo
Go To Bottom

Printable Version  
[ Total Views: 667 | Total Replies: 6 | Thread Id: 88168 ]
Author: Subject:  Fuel Pump Problem
Memberphantom
Wolfsburg Wizard
***


Avatar


Posts: 598
Threads: 196
Registered: March 28th, 2004
Member Is Offline

Location: Canberra ish
Theme: UltimaBB Pro Blue ( Default )
Mood: Where does this wire go?

posted on January 16th, 2011 at 07:00 AM
Fuel Pump Problem


Morning all,

I have to change the fuel pump after a long running issue - its nothing flash - stock 1600 in a '72 Kombi.

The pump going in is a new Brazilian one, the changeover went OK and it started nicely when fitted. However it only ran around 2 minutes and then died, very much like if it were starved of fuel.

I tried changing the hoses on the pump, no change. I now believe the pump isn't working. I think it ran initially with leftover fuel in the hose to the carby but is now starved.

What I didn't notice until I pulled it back out is that the old VW pump had the pump 'tongue' protruding from the bottom of the base, where it contacts with the rod from the block.

The new pump has the tongue slightly inside the case, I believe the rod isn't contacting the tongue enough to make the pump function.

I note the black rubber piece that sat under the original pump, like a large gasket between the pump and the body. Should I remove that so that the pump will make contact, or will that be too much?

Pics below.

Advice appreciated, I can't get the car to a VW mechanic currently and have to fix it at home. Thanks!

http://members.dodo.com.au/~phantoms1/pump1old.jpg
Old pump

http://members.dodo.com.au/~phantoms1/pump2new.jpg
New pump, recessed tongue, and rubber block




Super ModeratorBizarre
Super Moderator
The artist formerly known as blue74l
*******

Rank Avatar

Avatar


Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline

Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )

posted on January 16th, 2011 at 08:04 AM



yeah - think you will find there are 2 different rod lengths

You will need a longer rod




Futue te ipsum!!!
Super Moderatormatberry
Super Moderator
Go hard or go home
*******

Rank Avatar

Avatar


Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline

Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3

posted on January 16th, 2011 at 08:37 AM



Yep, the angled pump (your old one) is used with the alternator which has the short pushrod. Your new pump is to suit a generator and requires a longer pushrod but wiill possibly have clearance issues if you have an alternator fitted.



Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
http://i375.photobucket.com/albums/oo199/mattberry-photo/20032011354-2.jpg
MemberPartyHatCentral
Slammed & Awesome Dubber
**


Avatar


Posts: 94
Threads: 14
Registered: April 25th, 2005
Member Is Offline

Location: Bris Vegas
Theme: UltimaBB Pro Blue ( Default )
Mood: Yet to be confirmed

posted on January 16th, 2011 at 08:46 AM



No problem with fit - you will need a 108mm pushrod (your old one will be only 100mm).
Memberphantom
Wolfsburg Wizard
***


Avatar


Posts: 598
Threads: 196
Registered: March 28th, 2004
Member Is Offline

Location: Canberra ish
Theme: UltimaBB Pro Blue ( Default )
Mood: Where does this wire go?

posted on January 16th, 2011 at 08:50 AM



Thanks all, and yes its just a genny in there.

I suppose the next question is whether the pushrod is an easy job to change? Is it fitted to the mechanicals below (and therefore need an engine pull) or does it somehow get fitted from the top?

Thanks heaps.




Super Administratorbarls
A.k.a.: Mr indestructible
Super Administrator
Causer of Chaos and Mayhem
*********

Rank Avatar

No Avatar


Posts: 9467
Threads: 295
Registered: June 22nd, 2004
Member Is Offline

Location: cruising in denistone east
Theme: UltimaBB Streamlined2
Mood: indestructible? and listening to the voices

posted on January 16th, 2011 at 08:55 AM



they just pull straight out mate and is just a straight rod.



“We all pay for life with death, so everything in between should be free.” Bill Hicks
the chaos project - click me

http://www.goats.com/store/images/banner_destroy.png
Super Moderatormatberry
Super Moderator
Go hard or go home
*******

Rank Avatar

Avatar


Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline

Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3

posted on January 16th, 2011 at 08:59 AM



^^^ yep, just pull the old one out (leaving the plastic spacer block), but check the new pushrod at maximum up stroke, you want 13mm protruding from the gasket.



Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
http://i375.photobucket.com/albums/oo199/mattberry-photo/20032011354-2.jpg


  Go To Top


Powered by GaiaBB, © 2011 The GaiaBB Group
(C) 2001-2024 Aussieveedubbers

[ Queries: 40 ] [ PHP: 2.9% - SQL: 97.1% ]