| [ Total Views: 776 | Total Replies: 8 | Thread Id: 90090 ] |
|
|
 beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on April 27th, 2011 at 09:38 PM |
|
|
Should I install a sand seal?
I have been getting a mist of oil over my engine after long fast runs for a while now, and thought it was from the dodgy cork seal in the oil filler
cap.
I replaced it over Easter, and cleaned the engine. After I drove back to work yesterday (a bit over 700km), I had a line of oil spray on the tinware
in line with the back of the crank pulley.
Is this where I should look at installing a sand seal, stock up on degreaser, or is there some other cause that I hadn't considered.
From your ole' mate Jeff
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on April 27th, 2011 at 09:53 PM |
|
|
hows your breather??? pipes
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on April 27th, 2011 at 10:15 PM |
|
|
Should be OK. I have breather pipes running from the tappet covers to a breather box, my case breather goes to both the breather box and the vent
under the engine, and the breather box vents to the RH carby.
Is there any way I can test it?
Just thinking, I also give the car it's 600,000km service (70,000km for the engine) on the weekend - I wonder if I have ended up with the oil level
to high.
I will check tomorrow.
From your ole' mate Jeff
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on April 27th, 2011 at 10:17 PM |
|
|
Hi Jeff
Also have look at the reverse thread on the slinger, they can get blocked.
Steve
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on April 27th, 2011 at 10:26 PM |
|
|
Hmmm. Will have a look at it next time I am home for long enough.
From your ole' mate Jeff
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on April 27th, 2011 at 10:34 PM |
|
|
if it has just happened after the service then your oil level is probably a tad high....I would be checking that first
T
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on April 27th, 2011 at 10:47 PM |
|
|
I haven't cleaned it for a while, and I think I was getting oil spray from the gasket in the oil filler cap and a leaking rear main oil seal (that I
also replaced on the weekend), so I am not sure if this has just started or not.
I will check the oil level tomorrow though.
From your ole' mate Jeff
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on April 27th, 2011 at 10:48 PM |
|
|
I just use degreaser under My beetle but that looks like you have too much oil in Your engine..
a mist after 700kms is probably OK IMHO....
but the only time I've had actual oil on the tinware is after blocking the breather by mistake.... lol
but it really came out.... so Your breather must be OK...
I always have been thinking why not use an O ring there...???
but seeing You don't go near sand.... 
I think You may need a highway seal....
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on April 27th, 2011 at 11:00 PM |
|
|
| Quote: | Originally
posted by 68AutoBug
but seeing You don't go near sand....
I think You may need a highway seal....
LEE
|
What about a mud seal. lol
From your ole' mate Jeff
|
|
|
