| [ Total Views: 631 | Total Replies: 14 | Thread Id: 91420 ] |
|
|
 bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
 posted on July 6th, 2011 at 03:35 PM |
|
|
window rubbers, can they be stretched?
Bought a brazilian set of window rubbers 12 months ago, been sitting around till i came to the day of eventually needing them, which was today.
We barely got the windscreen rubber on...
the rear window and both rear quarter rubbers are rediculously tight and too small to fit.
the kit was for a 65-71 beetle, and came from a bag labelled such.
I know i should have bought german, but lets just say the heading of "Premium quality' is widely used regardless, and hence thought it was ok.
I'm a bit down about this. fitting the windows after all these years of them being off was going to be a milestone.
Chris.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
h
A.k.a.: Towely BuMpEr KING! ILLegal ALIEN on a roadtrip
Scirocco Rare
fractals - an ever changing lifestyle
Posts: 7670
Threads: 375
Registered: February 3rd, 2005
Member Is Offline
Location: noosa hillbilly 'yee har'
Theme: XMBX Pro Green
Mood: A T3 is not a Kombi - stop waving at me
|
| posted on July 6th, 2011 at 03:56 PM |
|
|
being winter they are prolly cold n contracted a bit, so maybe leave em in the sun for a few hours n they will be more flexi n will prolly fit up
nicely
give that a go before whacking em in a moderate oven for about 30min 
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on July 6th, 2011 at 04:57 PM |
|
|
thanks, will give that a whirl tomorrow. we got one rear quarter done... the rear window is being a real mungrel. we tried some hot & soapy water
and many colourful words  , almost had it... then we called it a day as
the bottom popped off. will try again tomorrow.
I guess a tight fit means it will be a good seal i spose 
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on July 6th, 2011 at 05:31 PM |
|
|
They all can be Very hard to fit Chris...
My rear window was terrible./..
My Son hits it with the palm of his hand to push it in..
Windscreen was hard as too...
the rear was a Brasillian rubber... looks great...
been in since 2004..
others were made in the USA... CIP1 rubbers..
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
REDKG
Officially Full-On Dubber
Posts: 327
Threads: 76
Registered: August 29th, 2002
Member Is Offline
Location: sutherland-sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 6th, 2011 at 05:56 PM |
|
|
agreed, they are meant to be very tight. sit it in the sun for a while
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 6th, 2011 at 06:34 PM |
|
|
Warm them in some (not quite) boiling water and they should soften up a bit.
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on July 6th, 2011 at 06:38 PM |
|
|
Thats what you get when you buy crap you have explained it perfectly
|
|
|
Gracey
Wolfsburg Wizard
Posts: 511
Threads: 17
Registered: February 6th, 2003
Member Is Offline
Location: Beaudesert, Qld
Theme: UltimaBB Pro Blue
Mood: Itchy
|
| posted on July 6th, 2011 at 06:55 PM |
|
|
| Quote: | Originally
posted by vw54
Thats what you get when you buy crap you have explained it perfectly
|
Yeah right!!
I recently installed new side and rear window rubbers on one of my bugs and they were extremely tight, oh yeah they were West Coast Metric
rubbers!!!
As others have said warm then up, makes a huge difference.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on July 6th, 2011 at 07:15 PM |
|
|
| Quote: | Originally
posted by bajachris88
Bought a brazilian set of window rubbers 12 months ago, been sitting around till i came to the day of eventually needing them, which was today.
We barely got the windscreen rubber on...
the rear window and both rear quarter rubbers are rediculously tight and too small to fit.
the kit was for a 65-71 beetle, and came from a bag labelled such.
I know i should have bought german, but lets just say the heading of "Premium quality' is widely used regardless, and hence thought it was ok.
I'm a bit down about this. fitting the windows after all these years of them being off was going to be a milestone.
Chris.
|
The rubbers may be incorrect for Your year model Chris
I bought a set of top quality USA made rubbers and the rear one was for a 71> rear window which was too Big
hence the Brasillian rear...
there are many factories in Brasil making these bits so the quality can vary a lot...
My Brasilian door rubbers aren't good quality but I have a new set of USA made ones...
its the luck of the draw... lol
LEE
PS: and many of Us don't have money to burn... lol
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 6th, 2011 at 08:19 PM |
|
|
Heat them up, there's nothing wrong with heating rubber seals up prior to fitting. I work at the Holden factory at Elizabeth and they have radiant
heat lamps hanging over all kinds of rubber parts on the side of the line to make them easier to fit, everything from door seals to rubber hoses.
|
|
|
zocstar
Officially Full-On Dubber
Posts: 279
Threads: 21
Registered: May 3rd, 2010
Member Is Offline
Location: Wollongong NSW
Theme: UltimaBB Pro Blue
|
| posted on July 6th, 2011 at 09:05 PM |
|
|
You can use glass cleaner to lube them up a bit also.
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on July 6th, 2011 at 10:02 PM |
|
|
I worked for a window company a number of years ago, and we always had old deep fryers full of hot water (but turned down low so they didn't boil)
with a drop of detergent in it to soften the rubbers before glazing aluminium windows.
I have been out on re-glazes where the old rubbers were hard and brittle, but a soak for a few minutes in hot soapy water, and they would be flexible
for a few minutes untill they cooled down again.
From your ole' mate Jeff
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on July 7th, 2011 at 01:56 AM |
|
|
| Quote: | Originally
posted by waveman1500
Heat them up, there's nothing wrong with heating rubber seals up prior to fitting. I work at the Holden factory at Elizabeth and they have radiant
heat lamps hanging over all kinds of rubber parts on the side of the line to make them easier to fit, everything from door seals to rubber hoses.
|
interesting...
the Cruze is looking very good...
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on July 7th, 2011 at 02:40 PM |
|
|
Thanks guys,
the soapy hot near boiling water soak technique did the job... still was alot of effort... hands hurt so bad.
the windows are now installed
wipper snipper line for the way
now to doors.... dam if i can get these door windows and regulators out!
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on July 7th, 2011 at 05:01 PM |
|
|
| Quote: | Originally
posted by bajachris88
Thanks guys,
the soapy hot near boiling water soak technique did the job... still was alot of effort... hands hurt so bad.
the windows are now installed
wipper snipper line for the way
now to doors.... dam if i can get these door windows and regulators out!
|
Good one Chris
The windows and regulators etc are easy the tenth time You do it...lol
Just keep counting... lol
I have read where many people do actually break the window glass trying to remove it.... lol
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
