| [ Total Views: 862 | Total Replies: 13 | Thread Id: 91448 ] |
|
|
 Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 7th, 2011 at 06:11 PM |
|
|
Air/Fuel Gauge
Hey all.
Is an air/fuel ratio gauge a worthwhile investment?
What exactly are they for?
And what is the difference between wideband and narrowband??
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on July 7th, 2011 at 07:06 PM |
|
|
You ask difficult question sometimes...lol
I presume they would be used for multi carburetors or fuel injection??
I haven't got one... lol
wide band = 1 Mhz
narrow band... = 100 Khz ??
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 7th, 2011 at 07:51 PM |
|
|
I had one when i was setting my blower up, narrow band ones aren't that effective on a carbed car.
If you get one make sure to fit a heated sensor.
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 7th, 2011 at 11:29 PM |
|
|
| Quote: | Originally
posted by Joel
I had one when i was setting my blower up, narrow band ones aren't that effective on a carbed car.
If you get one make sure to fit a heated sensor.
|
Heated sensor?? More info?
Are they more a gauge to help with tuning then pretty useless after that??
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on July 8th, 2011 at 09:17 AM |
|
|
| Quote: | Originally
posted by Smiley
Are they more a gauge to help with tuning then pretty useless after that??
Smiley
|
Yes, but that depends on whether you wish to watch the A/F ratio, it will show up a change in A/F ratio. ie. a blocked jet or manifold leak etc.
Wide band has a much broarder range, a narrow band is useless in comparison, but they are the first generation that is used in many efi factory
systems to moniter and adjust the A/F ratio.
I use the Innovate Motorsports LM-2 with good results so far
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
ratty 63
A.k.a.: Rossco
Custom Title Time!
Posts: 1083
Threads: 74
Registered: October 1st, 2003
Member Is Offline
Location: Gold Coast, Qld
Theme: UltimaBB Pro Blue ( Default )
Mood: Just cured my shed envy! 
|
| posted on July 8th, 2011 at 09:21 AM |
|
|
A/F meters are mainly used for tuning. You see them used with EFI set-up quite a lot as there are many load points that have to be set in an EFI fuel
map.
I have also seen them fitted permanently to cars, but usually to vehicles used for racing (or to vehicles that the owners would like you to think
could be used for racing )
As you may already know, they use an Oxygen sensor fitted to the exhaust to 'read' the mixture. These Oxygen sensors come in a variety of styles
and must be matched to your A/F meter (or your EFI ECU). Oxygen sensors only work when they are in their operating temperature range (ie: hot).
I have only ever used the narrow band sensors with my EFI set-up and they are available in single wire, 3-wire and 4-wire versions. I assume that the
wide-band sensors would be available in the same configurations. The single wire sensors are not heated and therefore must be fitted fairly close to
the exhaust port in the head to ensure that they are kept at operating temp at all times - not really suitable for a VW. The 3 and 4 wire sensors are
both internally heated and are basically the same except that the 4 wire has an extra, independant earth wire for the sensor (this apparently makes
them more accurate than the 3 wire sensors... but only if the sensor cannot get a solid earth through the exhaust for some reason).
I have used a 3 wire sensor from a Ford Falcon in my EFI set-up and it works well. The sensor is mounted in the exhaust pipe where the 4 pipes come
together. As the 3 wire is heated it comes up to 'usable' temp fairly quickly.
R 
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 8th, 2011 at 09:31 AM |
|
|
| Quote: | Originally
posted by Smiley
| Quote: | Originally
posted by Joel
I had one when i was setting my blower up, narrow band ones aren't that effective on a carbed car.
If you get one make sure to fit a heated sensor.
|
Heated sensor?? More info?
Are they more a gauge to help with tuning then pretty useless after that??
Smiley
|
More or less what Matt said.
THe sensor just measures how much oxygen is in the exhaust flow and converts that into voltage.
EFI cars use it to control the mixture but becuase the computer with them makes mixture adjustments 100s of times a second it is far more accurate
than the manifold vacuum pulling fuel through a small jet so readings are all over the joint.
I've only used a narrow band one, wide band give far more accurate results.
I just had one of those LED strip style gauges
To the right of my boost gauge.
and hooked it to an oxygen sensor in the collector.
I used the heated sensor cos the runners on VW engines are just too long to keep enough heat there.
o2 sensors need to be above a set temp to operate.
Cos carbs are primitive fuel metering devices, nailing it would dump a heap of raw gas in so right up into the rich, then back of for gear change,
back to lean so with lots of bightly coloured LEDs on a carbed engine it was like have a frigging disco ball in the car at night.
I didn't get much value out of it.
Jetting is something you do more by feel.
|
|
|
Sides
A.k.a.: Dave Sidery
Veteran Volks Folk
Posts: 2220
Threads: 59
Registered: May 20th, 2007
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
Mood: Need... more... shed... time...
|
| posted on July 8th, 2011 at 09:38 AM |
|
|
I had the earlier Innovate setup (LM-1) and it was great with my twin IDF's... using it and just my numbty tuning skills got my engine ticking pretty
nicely... so much that 4 hours on a dyno with a pro only got an extra couple of ponies at the top end. Definitely worth having if you like messing
around the tune on your engine, jetting etc.
They're a must have with EFI basically - I now run an Innovate LC-1 and gauge, as the Haltech handles the logging and extra channels as standard.
Narrowband only tells you if your AF is richer or leaner than 14.7:1... they measure a "narrow band" either side of 14.7:1. Wideband setups tells
you exactly what you're AF is... usually the measurement band is something like 9:1 out to 20:1, and so are far more useful.
A heated sensor is literally what it says... the sensor needs to be at a certain temperature to work, and so they put an electrically powered ceramic
heater element in it to get up to temp quicker (usually within around 30 seconds from start up). Most widebands use a heated sensor... a Bosch 4 wire
from modern VWs & Audis being the most common.
VWDCQ vice pres & web dude - vwdcqinc.org.au
Join a car club - get car peeps
My toys
'70 Hillclimb Bug 'Jezebel' w/- Haltech EFI - http://bit.ly/VwTNtQ
'60 KG Coupe - resto kinda started
01 New Beetle - gf's car, but I turn the spanners |
|
|
Thinker
Seriously Crusin Dubber
Posts: 162
Threads: 26
Registered: October 13th, 2008
Member Is Offline
Location: Narellan
Theme: UltimaBB Streamlined2
Mood: Contemplating
|
| posted on July 8th, 2011 at 02:00 PM |
|
|
funny this should come up as i have been looking at them my self, just as a set-up tool for a set of twins i just put on. i have had all sorts of
trouble getting it running right.
and i figured for the price of a gauge kit and my time in the garage it would work out cheaper than a expert, and hey i will learn a new skill.
keep the info coming ****please****
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 8th, 2011 at 02:18 PM |
|
|
| Quote: | Originally
posted by matberry
| Quote: | Originally
posted by Smiley
Are they more a gauge to help with tuning then pretty useless after that??
Smiley
|
Yes, but that depends on whether you wish to watch the A/F ratio, it will show up a change in A/F ratio. ie. a blocked jet or manifold leak etc.
Wide band has a much broarder range, a narrow band is useless in comparison, but they are the first generation that is used in many efi factory
systems to moniter and adjust the A/F ratio.
I use the Innovate Motorsports LM-2 with good results so far
|
Hey Matt.
Is this the gauge you're talking about??
http://www.innovatemotorsports.com/products/MTXL.php
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
RISKY4LIFE
Officially Full-On Dubber
Posts: 308
Threads: 5
Registered: July 4th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 8th, 2011 at 02:34 PM |
|
|
i was just about to pull my exhaust off and do some work on it and weld in the thread for a sensor
what size thread would it be? and are they all the same?
thanks
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 8th, 2011 at 02:47 PM |
|
|
They are all the same thread.
From memory they are M18x1.5
what ever a spark plug is they are the same as that.
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 8th, 2011 at 03:05 PM |
|
|
Joel is correct. I just looked up the thread size for the sensor in that gauge I posted above.
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on July 8th, 2011 at 03:30 PM |
|
|
Yep, but I've actually got the one below as a workshop tool, it data logs and hooks up to a laptop....among other things
http://www.innovatemotorsports.com/products/lm2.php
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
