| [ Total Views: 733 | Total Replies: 4 | Thread Id: 91627 ] |
|
|
 tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 18th, 2011 at 04:04 AM |
|
|
PVC pipe for radiator coolant
About to plan my conversion to EA81 on my trike as mentioned elsewhere in the forum.
Can anyone tell me if PVC say 32mm or 40mm pipe can be used for radiator coolant from and to the radiator from the engine? Does anyone know the
specifications of the product eg pressure, chemical resistance and temperature tolerance?
Just asking...thought if it was feasible it would be so much easier/cheaper hooking up a custom radiator in lieu of s/steel pipe.
Alternatively are there any rubber manufacturers that make long lengths of flexible radiator hose suitable for this now common need?
|
|
|
DubCrazy
A.k.a.: steff
Custom Title Time!
Posts: 1295
Threads: 145
Registered: July 18th, 2003
Member Is Offline
Location: Gladstone Qld
Theme: UltimaBB Pro Blue
Mood: painting anything in front of me
|
| posted on July 18th, 2011 at 07:24 AM |
|
|
in one word NO.. if your thinking of useing normal pvc piping they use for plumbing ad such it will struggle to hold the pressures and if it manages
to cope with that it will turn brittle very quickly and split/explode. I belive you can get high presure pvc piping easly enough but its not
cheap..
for what it will cost you to buy pvc you would be able to make it out of steel. Just goto your local exhaust fabricator and they will have all u would
need for a cheap price plus they can put bends etc where needed.
when i rebuilt my ea82t in my baja i replaced all piping this way for very little cost.
steff..
Life with out a v-dub is no life at all!!!!!
|
|
|
Bone
Officially Full-On Dubber
Posts: 299
Threads: 43
Registered: August 9th, 2009
Member Is Offline
Location: Cooroy
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 18th, 2011 at 07:44 AM |
|
|
On my ea81 baja I used the 32mm rural pipe from local produce store which was just to test the engine. I didnt think the pressure was an issue as the
radiator cap was 13psi. Anyway to cut a long story short it didnt look like failing at any piont but I used 90 deg radiator pipes for the bends with
good radiator clamps. (used for 2 yrs and looked like new when removed). I think it was the green stripe rural pipe (not garden).
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on July 18th, 2011 at 10:39 PM |
|
|
I used Water Suction Hose in our bus. It is rubber with a spiral wire core. Not as cheap as PVC, but I used 5 metres of the stuff and it cost less
than $100, so it wasn't ridiculous expensive compared to other aspects of the conversion.
|
|
|
mactaylor
Custom Title Time!
Posts: 1005
Threads: 54
Registered: August 14th, 2007
Member Is Offline
Location: Albury
Theme: UltimaBB Pro Blue
Mood: even my dog is german
|
| posted on July 19th, 2011 at 08:20 AM |
|
|
most new houses use plastic hot water pipes that take town pressure thats about 20psi and 75geg and there is a plastic product for high temp and high
pressure but its not cheap cant remember what its called but reece industrial stock it. personaly id use alluminium pipe not vry exy, get you exhaust
dude to bend it to shape, you can buy good looking clamps and fixtures from enzed.
EVERLAST CONCRETE TANKS
1800 552 123
|
|
|
