| [ Total Views: 835 | Total Replies: 7 | Thread Id: 92086 ] |
|
|
 shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on August 11th, 2011 at 06:50 AM |
|
|
Cleaning pistons and heads - what is the best way?
After chasing an oil leak from an oil cooler seal, i got bored so i thought i'd clean up my engine which i have never stripped down since owning.
I found a bit of carbon build up on my pistons (a couple of millimeters thick!) and heads, and would like to remove it to check for damage so what is
the best, safest way without paying someone to do it? Valves will still be attached to the heads.
I've read oven cleaner, diesel, carb cleaner, brake cleaner, metho, etc, but will any of these damage the parts? I've also attached pics so if you
see anything unusal in them let me know.
Cylinder 3 & 4 head
Piston 3
Piston 4
Pushrods - notice on 2nd from left there is a mark, this can be felt when i run my finger across it. What could this be from and should i repalce
them?
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on August 11th, 2011 at 09:22 AM |
|
|
if your not getting a valve grind etc DONT clean any thing.
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on August 11th, 2011 at 09:30 AM |
|
|
| Quote: | Originally
posted by ian.mezz
if your not getting a valve grind etc DONT clean any thing.
|
Not even the pistons? Could you explain why that is?
Does everything look okay so far? How about that marked pushrod?
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on August 11th, 2011 at 01:57 PM |
|
|
you can clean it with a piece of alluminium sheet nuthing to hard so u dont scratch the surfaces
|
|
|
 Peter Leonard
Super Moderator
Volatile
Posts: 1456
Threads: 52
Registered: April 18th, 2003
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: shiny
|
| posted on August 11th, 2011 at 03:47 PM |
|
|
good way to raise the compression, filling the head with carbon and baked on crap  put on some new aftermarket heads while it's apart, great chance to play with it! The pushrod looks like it's been rubbing
somewhere, maybe one of the pushrod tubes was bent for a while, or it was off its rocker and rolling about in there for a while (or maybe on a
previous motor.. these things have chequered and interesting pasts). Worth replacing if you plan on reiability, depends on how deep the mark is and
how hard you're pushing the rods... I'd replace it.
let sleeping dubs lie
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on August 11th, 2011 at 03:58 PM |
|
|
| Quote: | Originally
posted by shokwave2
| Quote: | Originally
posted by ian.mezz
if your not getting a valve grind etc DONT clean any thing.
|
Not even the pistons? Could you explain why that is?
Does everything look okay so far? How about that marked pushrod?
|
cause you just don't do it, you don't pull motors apart to clean them , you pull them apart to recondition them.
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on August 11th, 2011 at 04:10 PM |
|
|
Fair enough. I just thought a build-up of carbon in various areas may have affected my motor.
So in other words pistons, cylinders and heads must be all recondtioned together?
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on August 11th, 2011 at 06:55 PM |
|
|
| Quote: | Originally
posted by shokwave2
Fair enough. I just thought a build-up of carbon in various areas may have affected my motor.
So in other words pistons, cylinders and heads must be all recondtioned together?
|
Are you going to re ring it? If you are I suggest you also go the rest of the way as the extra load is then transferred to the next weakest point
which will be the bearings.
|
|
|
