| [ Total Views: 1083 | Total Replies: 11 | Thread Id: 92398 ] |
|
|
 Marilyn71
Seriously Crusin Dubber
Posts: 124
Threads: 26
Registered: August 16th, 2011
Member Is Offline
Location: Ballina NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 09:04 AM |
|
|
breaking in a rebuilt engine
Hi all I'm getting my old 1500 rebuilt and upgraded to a twin port 1600. New heads, valves, barrels, cams pistons etc.
Is there any special breaking in process for driving the car when back on the road?
|
|
|
66brm
Seriously Crusin Dubber
Posts: 140
Threads: 4
Registered: November 13th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 09:33 AM |
|
|
Take it easy for the first 1000 k's ,change your oil at the factory intervals for a new engine, and check your tappet adjustment watching for any
abnormal changes. Listen to it as you drive it around for any new, strange noises and get them checked out. Once this is all sorted then you should
get a long reliable service life out of it.
|
|
|
Marilyn71
Seriously Crusin Dubber
Posts: 124
Threads: 26
Registered: August 16th, 2011
Member Is Offline
Location: Ballina NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 09:56 AM |
|
|
Thanks for the quick reply. I'll do all that.
Is there any limits on road speed and varying the throttle/rpms?
Years ago it was common to have limits set to 80kmh not to exceed and not sit on one speed for any extended periods on water cooled rebuilds I've
had.
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 10:17 AM |
|
|
Also I think its important for the initial break in of the cam/followers. Not sure as so many different people say so many different things. I let my
engine build do my initial start up. But i think trun it over with no plugs in to build oil pressure until the light goes out. then once it starts....
talk to your enginer builder or wait for people like Matt Berry, Dangerous or similar on here for advice.
Once mine was on the road ie 0km after cam break in, it was don't flogg it initally, take it for a longish drive to fully heat up, vary revs and
load, but don't flog it. Oil changed straight after initial fire up, then 200km, then 1000km, then the normal 3000 to 5000 km depending if it had
raced or just been on the street.
if you had the engine built, just do what the engine builder says....
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
Marilyn71
Seriously Crusin Dubber
Posts: 124
Threads: 26
Registered: August 16th, 2011
Member Is Offline
Location: Ballina NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 12:46 PM |
|
|
Thanks mate
|
|
|
Paulc1964au
Custom Title Time!
Posts: 1627
Threads: 59
Registered: March 5th, 2010
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 05:24 PM |
|
|
1000k's at the rate i drive my car when i build the new engine I will never get to break it in lol
|
|
|
vvwbeetle
Officially Full-On Dubber
Posts: 234
Threads: 63
Registered: April 18th, 2011
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Upsetting bikes on the Old Road
|
| posted on August 30th, 2011 at 07:37 PM |
|
|
Hi,
I've had my new engine in for around 180miles.I'm not valve bouncing it but I'm not treating it like a baby either. All good so far.
The engine builder has told me to drive it normally so I am. It will have it's first service at 1000kms and have the tappets adjusted etc.
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 07:54 PM |
|
|
If its a new cam then an initial break in is required.
That is Do not idle for say 20 mins. You need to keep the revs at about 2500 for that 20 mins. Also i hope you used a proper cam lube on the lobes
and lifter bases.
Once you have done that initial 20 min break in. After that 20 mins, put it onto the road, stick it in say 2 nd or 3 rd and accelerate from 20- 70 ks
three or four times. This puts the engine under heavy cylinder pressures and beds yours rings, after that, do whatever you want to it, Flog it if you
want, just dont take it real gentle
|
|
|
Marilyn71
Seriously Crusin Dubber
Posts: 124
Threads: 26
Registered: August 16th, 2011
Member Is Offline
Location: Ballina NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 10:05 PM |
|
|
Thanks for all the advice. I've got a 200k trip to Brissy this week so its good to hear that a sensible drive is in order.
By the way Paul I looked at your 69 Bug refurb. pics today. What an outstanding car!!! I just think to myself ...one day...one day my girl will look
as good.
I hope to get her back tomorrow. At least it will stop me driving the wife nuts about having the bug back
|
|
|
cnfabo
Custom Title Time!
Posts: 1353
Threads: 140
Registered: April 15th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 30th, 2011 at 10:40 PM |
|
|
pobjoy told me to take it for a drive for ten minutes,no tune up or timing..just try and get it close before start up... change through gears etc. no
stop start driving, so find some back roads... then come back and dont let it idle, switch off and drain the oil....then the first 1000kms just drive
it...no thrashing it...
hope this helps and im sure a lot of people will disagree.....but i know who id listen too....
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on August 30th, 2011 at 11:01 PM |
|
|
I'm with Clinker42. Cam break-in, 2000 rpm for 20 minutes, change oil/filter and adjust valves then quick tune and get it loaded up. Half a dozen
full power from low rpm to near redline if all sounds right to bed the rings. Fine tune and drive normal - hard, not to maintain sustained rpm or
light load, highway cruising vary speed occasionally with periodically lifting off throttle momentarily to aid in upper cylinder lubrication.
Don't lug engine and don't pussy it. A lazy run-in will be a lazy engine. Many of the worlds best engine builders stand by a variation of that
statement.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Marilyn71
Seriously Crusin Dubber
Posts: 124
Threads: 26
Registered: August 16th, 2011
Member Is Offline
Location: Ballina NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 31st, 2011 at 07:52 AM |
|
|
Thanks guys, a bit of a vigour on the right foot sounds like it will help. Certainly dont want a lazy engine.
|
|
|
