| [ Total Views: 823 | Total Replies: 12 | Thread Id: 93107 ] |
|
|
 karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 09:16 AM |
|
|
Difficult cold start and running rough
Need help debugging the problem. The engine is an 1880 with a 34PICT carb, standard dizzy with electronic ignition
On most cold mornings, it is difficult to start. I can tell its firing on one or maybe two cylinders so hardly cranking. I have to floor the pedal to
keep it going then after a minute, the other cylinders start kicking in and the revs will pick up. It will take maybe 15 minutes by the time it is
running smoothly
I replaced the spark plugs already. Could it be a bad coil or bad HT leads?
|
|
|
ratty 63
A.k.a.: Rossco
Custom Title Time!
Posts: 1083
Threads: 74
Registered: October 1st, 2003
Member Is Offline
Location: Gold Coast, Qld
Theme: UltimaBB Pro Blue ( Default )
Mood: Just cured my shed envy! 
|
| posted on October 10th, 2011 at 09:29 AM |
|
|
Is this something that has just started happening or has it been going on for a while now?
R 
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 09:34 AM |
|
|
Going on for a while
|
|
|
chillihilli
Commited Dubber
Posts: 64
Threads: 19
Registered: October 13th, 2010
Member Is Offline
Location: Melbourne Victoria
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 10:24 AM |
|
|
I have limited knowledge but - Have you checked your plugs again? In aviation an engine sometimes ran rough prior to take off. We used to run it up to
2000 rpm then lean out the carb - this causes the cylinder head to heat up and burn off crap on the plug. You are doing a similar thing by flooring it
and warming it up.The engine would then run smoothly. I would check if your plugs are fouled. If so it would point to a carb mixture and/or timing
issue.
71 Clementine Superbug Autostick
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 11:34 AM |
|
|
It could well be the issue because its running very rich. Mixture screw is jammed so I can't adjust it but I do have a near new 34PICT which I was
planning to use. Will do that first and see
Thanks
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 12:17 PM |
|
|
By they way, is this was the problem, why would it happen only in the morning?
|
|
|
stagvee40
Commited Dubber
Posts: 68
Threads: 14
Registered: January 20th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 11th, 2011 at 06:28 PM |
|
|
Hmmmmm sounds like your ignition timing is way to advanced. You do know that the marks on the crank pulley are 7.5deg and 10deg, neither is Top dead
centre.
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 18th, 2011 at 01:47 PM |
|
|
Thanks Mate, yes I am aware of what the marks represents
I replaced the one on the left with the one on the right (near new 34PICT) and its running much better now. However I am getting a small amount of
backfire at idle when the engine is still warming up. Running too lean?
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 18th, 2011 at 02:43 PM |
|
|
| Quote: | Originally
posted by karmannghia60
Thanks Mate, yes I am aware of what the marks represents
I replaced the one on the left with the one on the right (near new 34PICT) and its running much better now. However I am getting a small amount of
backfire at idle when the engine is still warming up. Running too lean?
|
Hi
the carby on the Left has a piece missing o n the top shaft
the carby on The Right has it...
I don't think Your automatic choke was working...
turn the mixture screw in until the engine dies a bit [revs reduced] and unscrew about 1/2 a turn... see how it goes..
have You checked the choke flap?? choke adjustment?
when starting the engine...
You should push the accelerator to floor once..
then take Your foot off the pedal..
this operates the automatic choke....
then turn the key....
it should start and idle fairly high depending on the choke adjustment ...
what distributor are you using??
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 18th, 2011 at 03:16 PM |
|
|
Thanks Lee
You are right about the missing part, I never noticed before!
i am running a standard vacuum advanced dizzy
The way I adjusted the mixture is different from what you described. I usually turn the screw till I get to the highest revs them turn it in 1/4 to
1/2 turn
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on October 18th, 2011 at 03:36 PM |
|
|
what idle jet are you running for your bigger donk?
55 or 60 might not cut it for 1880cc. Mind you i get that kinda rubbish running on my 1600, but is a POS 34 pict 4 that is VERY well aged.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 18th, 2011 at 05:02 PM |
|
|
| Quote: | Originally
posted by karmannghia60
Thanks Lee
You are right about the missing part, I never noticed before!
i am running a standard vacuum advanced dizzy
The way I adjusted the mixture is different from what you described. I usually turn the screw till I get to the highest revs them turn it in 1/4 to
1/2 turn
|
OK
Yes
screw the screw in until You hear the slightest rev drop
[hesitation] and screw it out about 1/2 a turn...
engine must be hot to do this...
its probably running too rich...
cheers
LEE
PS: I always give it another 1/4 turn out to be sure...
a lean running beetle isn't good...
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Lucky Phil
Wolfsburg Wizard
Posts: 480
Threads: 16
Registered: August 1st, 2010
Member Is Offline
Location: Adelaide SA
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm a legend in my own lunchtime!
|
| posted on October 18th, 2011 at 05:16 PM |
|
|
I would bet that the mainjet would want to be bigger if you are running a larger 1880 engine too.
|
|
|
