| [ Total Views: 547 | Total Replies: 4 | Thread Id: 93579 ] |
|
|
 bluebus
Seriously Crusin Dubber
Posts: 150
Threads: 30
Registered: September 16th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy happy joy
|
| posted on November 5th, 2011 at 02:05 AM |
|
|
66 beetle accelerator question
I'm having issues with my accelerator pedal. The pedal is stiff and hard to push. Seems it's not the pedal assembly but the accelerator arm
itself. After taking off the access panel to check out where the arm attaches to the cable, I found that the accelerator arm is pushing too far
towards the passenger side, and rubbing on the access panel cover. Seems that the washer on the driver's side where the arm comes out of the pedal
cluster no longer fits the arm and is just free floating, so the arm can move a few mm back and forth. When I pull the arm towards the driver's side
the pedal moves freely again.
So my question is, how can I replace this washer so that the arm is held in place properly? Can I just undo the circlip on the passenger side of the
arm and pull out the arm, or do I have to remove the entire pedal cluster? Quick and easy solutions welcome 
66 Beetle & 66 Austin 1800... makes for a very stylish footpath  |
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on November 5th, 2011 at 06:50 AM |
|
|
Unfortunately the only way to replace that thrust washer is as you said, remove the pedal assembly so the throttle pedal cross shaft can be removed.
Normally, while your there, expect a major clean up of the pan and pedal assembly.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
shaihulud
Custom Title Time!
Posts: 1448
Threads: 197
Registered: November 4th, 2005
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 5th, 2011 at 09:43 AM |
|
|
I agree with mattberry. It's going to be compete removal and clean up job.
You will probably find that the clutch cable hook is worn and that it is a good thing that you have removed it. Weld some metal into the hook and file
it down.
If you have difficulty re-fitting the cable, I suggest drilling a small hole in the tip of the hook and the base of the hook and wire the cable in
using some soft tie wire. It then won't pop off when juggling the pedal assembly back in.
|
|
|
bluebus
Seriously Crusin Dubber
Posts: 150
Threads: 30
Registered: September 16th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy happy joy
|
| posted on November 5th, 2011 at 12:05 PM |
|
|
Damn... thought as much. Thanks for the tips. If the crud under the access panel cover is anything to go by it's going to be very grateful for a
good cleanup!
Cheers,
Angela.
66 Beetle & 66 Austin 1800... makes for a very stylish footpath |
|
|
bluebus
Seriously Crusin Dubber
Posts: 150
Threads: 30
Registered: September 16th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: happy happy joy
|
| posted on November 5th, 2011 at 01:13 PM |
|
|
Question part 2... What about using a circlip? Just thinking that if I can get one the right size, then perhaps I can install it over the arm without
having to remove the assembly. Thoughts?
66 Beetle & 66 Austin 1800... makes for a very stylish footpath |
|
|
