| [ Total Views: 716 | Total Replies: 5 | Thread Id: 93791 ] |
|
|
 Craig S
A.k.a.: Craig
Wolfsburg Wizard
Posts: 635
Threads: 83
Registered: May 26th, 2008
Member Is Offline
Location: Sunny Western Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: In the mood for change
|
| posted on November 14th, 2011 at 09:13 AM |
|
|
Type 3 Engine into Beetle - Dipstick location
So yesterday I was pulling more tinware and stuff off the engine so that it can be put in a Beetle, and apart from trying to figure out how the heck
you'd change sparkplugs in a Type3, my main question is dipstick location.
It's a universal case, and I've removed the type 3 dipstick and put the block off plate in place, but from what I can see there is a metal plug in
the position where the type 1 dipstick would go.
Is that going to be able to be removed without splitting the case because of the metal shavings?
Are there any other options?
Can I retain the type 3 dipstick and put an additional slot in the type 1 tinware for it to poke out of?
Thanks. 
Craig
1969 Beetle - June
1974 L Bug - Gwendolyn
2002 Bora V6 4Motion - Anita
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on November 14th, 2011 at 10:08 AM |
|
|
U need a universal dipstick, basically its a block off with a tube attached.
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
Craig S
A.k.a.: Craig
Wolfsburg Wizard
Posts: 635
Threads: 83
Registered: May 26th, 2008
Member Is Offline
Location: Sunny Western Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: In the mood for change
|
| posted on November 14th, 2011 at 11:32 AM |
|
|
Thanks for that. I gather it will be one of these:
http://www.vwparts.net/BP3068.html
1969 Beetle - June
1974 L Bug - Gwendolyn
2002 Bora V6 4Motion - Anita
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on November 14th, 2011 at 01:20 PM |
|
|
thats the one 
I gots the same fitted on my type 3 donk.
Only other difference is the oil pressure sender in the oil cooler on the type 3's compared to being in the block like the bug donks. if you are
going to do an 'upright' conversion (IE: fit bug tinwear) you will need to use the type 3 oil cooler for its oil pressure sender (both bug and type
3 oil coolers are the same in geometry etc).
The oil cooler in a dog house fashion fits the same as a bug. You will need to use the bug oil cooler adapter (that the oil cooler bolts to, and that
bolts onto the block). Just be aware that you (if like my type 3 donk) may have to drill the hole for bolting the oil cooler adapter thingo a little
wider on the flange that goes over the passenger side bank for the oil cooler adapter.
Don't worry, its on the flange, and thus no swarf can get in the block as the shavings just go over the barrels.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on November 14th, 2011 at 02:53 PM |
|
|
You could drill a hole in the round part of the dipstick holder/block off plate and fit the temperature sender there...
or find a type 3 doghouse oil cooler... with the oil sender hole..
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Craig S
A.k.a.: Craig
Wolfsburg Wizard
Posts: 635
Threads: 83
Registered: May 26th, 2008
Member Is Offline
Location: Sunny Western Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: In the mood for change
|
| posted on November 14th, 2011 at 03:16 PM |
|
|
| Quote: | Originally
posted by bajachris88
Only other difference is the oil pressure sender in the oil cooler on the type 3's compared to being in the block like the bug donks. if you are
going to do an 'upright' conversion (IE: fit bug tinwear) you will need to use the type 3 oil cooler for its oil pressure sender (both bug and type
3 oil coolers are the same in geometry etc).
|
Um, could be interesting, because I'm pretty sure that it was previously fitted with an external oil cooler. There are at least three different
senders that I can see tapped in at various points, but I'll take photos once I've removed the rest of the timware and have a better view.
1969 Beetle - June
1974 L Bug - Gwendolyn
2002 Bora V6 4Motion - Anita
|
|
|
