| [ Total Views: 598 | Total Replies: 7 | Thread Id: 96126 ] |
|
|
 ClockworkMonkey
Seriously Crusin Dubber
Posts: 199
Threads: 29
Registered: October 7th, 2009
Member Is Offline
Location: Brisvegas
Theme: UltimaBB Pro Grey
|
| posted on March 30th, 2012 at 09:59 PM |
|
|
oil leaks
I've noticed that after every time I go for a drive there is a little bit of oil on the ground. This might sound dumb, but is this normal? I'm
planning to put a little more punch into my 1500cc sp but not sure if a leaky engine is worth working on. I never seem to have to fill much oil into
it and there is no smoke or really excessive oil burning smell
Any thoughts?
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 31st, 2012 at 10:50 AM |
|
|
You need to give it a really good degrease and see where it is leaking from
It could be as simple as one of the rocker gaskets or sump gasket.
Push rod tubes can be slightly more troublesome, same with say oil cooler seals or the front engine seal. A bit more work required to fix.
The difficult ones are if the motor has a heap of blow by / crank case pressure and is forcing oil out.
They "shouldnt" leak.
Mine doesnt leak at home where it is flat but seems to leave a drop at work where I have to park on a slight side incline.
Futue te ipsum!!!
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 31st, 2012 at 11:16 AM |
|
|
They don't leak, they are just marking their territory. lol
From your ole' mate Jeff
|
|
|
SebastienPeek
Custom Title Time!
Posts: 1657
Threads: 89
Registered: May 31st, 2011
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro White
|
| posted on March 31st, 2012 at 11:23 AM |
|
|
Mine is leaking quite a bit, not so good, but I guess everyone at work knows where Zelda sits 
Mine will take a little more effort to fix, have to take the LHS head off.
Seems the head itself has become displaced, which isn't good!
Any other car, water cooled that is, wouldn't run. But because no water can get into the engine in an air cooled monster, I am all good until it just
implodes...
Will need to remove the engine to fix mine. I hope it isn't the same for you and it is an easy fix!
Degrease the engine, clean it up, and find where that leak is coming from, then go from there!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on March 31st, 2012 at 11:30 AM |
|
|
| Quote: | Originally
posted by ClockworkMonkey
I've noticed that after every time I go for a drive there is a little bit of oil on the ground. This might sound dumb, but is this normal? I'm
planning to put a little more punch into my 1500cc sp but not sure if a leaky engine is worth working on. I never seem to have to fill much oil into
it and there is no smoke or really excessive oil burning smell
Any thoughts?
|
most VW engines do leak oil due to the expansion & contraction
because they get so hot due to the air cooling..
its common for sump gasket nuts to leak..
I use a new gasket kit with new washers every time and most times they don't leak - other times they do
tappet covers need new gaskets as the gaskets get compressed by the tappet cover
My last ones lasted about a year before they started to leak
unless they are replaced each time the tappets are adjusted.
and they need to be replaced carefully with no old bits of gasket cement or gasket left and perfectly clean,,
I then use permatex gasket cement on the tappet cover and grease on the engine surface..
and fit them carefully, as the gaskets can move as You fit them..
and they never leak until the gaskets get compressed from the pressure of the tappet cover clamps..
and there are different quality/material gaskets..
once a tappet cover gasket starts to leak it can drip a lot of oil
push rod tube seals can also leak...
they can crack or just leak due to the pushrod tubes expanding and contracting.
I always use permatex gasket cement on both sides of these seals to stop any leaks...
Some people don't use gasket cement... and that is why they leak...
If the breather pipe is blocked- oil can be blown out of the crankcase and will come out from behind the crankshaft pulley
and even the dipstick hole..
the engine can also leak where the case is joined across the centre of the engine ... due to heat expansion..
so all these things can be fixed..
so, no problem with an engine rebuild due to oil leaks..
cheers
LEE
PS: If I have an oil leak.. I degrease under My engine with spray can of foaming engine degreaser then hose it off..
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on March 31st, 2012 at 11:48 AM |
|
|
mine dont leak
|
|
|
OZ Towdster
A.k.a.: Andrew Westwood
Custom Title Time!
Keen to finish some projects
Posts: 1921
Threads: 132
Registered: December 7th, 2003
Member Is Offline
Location: Alexandra Hills Brisbane QLD
Theme: UltimaBB Pro Yellow
Mood: Having fun in our great land
|
| posted on March 31st, 2012 at 01:44 PM |
|
|
Lee i disagree with the use of permatex or any gasket goo on the pushrod tube seals . they should be just wiped in a light smear of high temp grease
as like you say the motors expand and contract with the heat .
Oh and dont use the shitty red rubber pushrod tube seals either as they go hard with the heat , the white silicon are the go
Don't let body work get in the way of real suspension travel
|
|
|
ClockworkMonkey
Seriously Crusin Dubber
Posts: 199
Threads: 29
Registered: October 7th, 2009
Member Is Offline
Location: Brisvegas
Theme: UltimaBB Pro Grey
|
| posted on April 1st, 2012 at 09:00 PM |
|
|
Hrm ... i'll have to give it a good degreasing and have a look where it is actually coming from... my driveway is sloped so that could be something.
i had the oil cooler seals? replaced a while ago so they are good... it was pissing oil out before i got it fixed. thanks for all the info guys!! do
most of you build / do all your own maintinance? i have no tools and no space so most of the work is done by my mechanic ... do they run like vw
maintinance courses or anything around the place?
|
|
|
