| [ Total Views: 542 | Total Replies: 7 | Thread Id: 96272 ] |
|
|
 smithy68
Wolfsburg Wizard
Posts: 419
Threads: 145
Registered: October 10th, 2010
Member Is Offline
Location: Adelaide S.A
Theme: UltimaBB Pro Blue
|
| posted on April 7th, 2012 at 05:36 PM |
|
|
Steering column
Hi, when removing the steering column from my 67 bug some ball bearings fell out of the column when removed from the car.
I was wondering if you can replace this bearing with a sealed type bearing, or do people just fit the bearings back in to the column.
Or worse case the column is now stuffed?
I am not even to sure where they sit in the column as I did 'nt notice them until they fell out.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on April 7th, 2012 at 10:53 PM |
|
|
I don't think they are a sealed type of generic bearing...
a specially made bearing for beetles..
later ones were nylon I think with ball bearings...
but I've never pulled any out..
I'd try and stick the balls back in if the casing isn't broken?
with lots of grease...
I'm sure someone on here has pulled one apart??
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
smithy68
Wolfsburg Wizard
Posts: 419
Threads: 145
Registered: October 10th, 2010
Member Is Offline
Location: Adelaide S.A
Theme: UltimaBB Pro Blue
|
| posted on April 7th, 2012 at 11:35 PM |
|
|
Thanks Lee, I hope some one has so they can enlighten me.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on April 8th, 2012 at 12:34 PM |
|
|
They are a cup and cone bearing, if you have lost your balls you should be able to purchase some loose balls in the correct size from bearing service,
it should have a wire clip that holds the bearing together, clean it up and use some grease to hold the balls in place, then you can reassemble the
race, the column has a clip and spring that loads a inner bearing sleeve, this applies the load to the race, a old manual will have a exploded view.
|
|
|
Old Dubber
Wolfsburg Wizard
Posts: 605
Threads: 25
Registered: August 26th, 2002
Member Is Offline
Location: Everton Hills, Brisbane, QLD, Australia 4053
Theme: UltimaBB Pro Blue ( Default )
Mood: great!
|
| posted on April 8th, 2012 at 02:54 PM |
|
|
The circlip has fallen off
Pages from my manual
and what it looks like in the flesh
|
|
|
LUFTMEISTER
Veteran Volks Folk
Posts: 2041
Threads: 119
Registered: July 13th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: BRISVEGAS in a state of flux
|
| posted on April 8th, 2012 at 03:19 PM |
|
|
Your meant to hit the nail with the hammer, not you thumb! Grahame Ouch.
Customer service is not dead in Australia.
Always after HAZET & MATRA & VW factory tools
|
|
|
smithy68
Wolfsburg Wizard
Posts: 419
Threads: 145
Registered: October 10th, 2010
Member Is Offline
Location: Adelaide S.A
Theme: UltimaBB Pro Blue
|
| posted on April 8th, 2012 at 06:34 PM |
|
|
Yea thanks heaps for that info, should be a breeze now Grahame, thankyou.
Thanks to vwo60 also.
|
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on April 13th, 2012 at 07:00 PM |
|
|
Have a look at the latest Hot VW's mag. There is an article about the steering column
Cheers....Wayne
|
|
|
