| [ Total Views: 1109 | Total Replies: 11 | Thread Id: 97525 ] |
|
|
 Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on June 21st, 2012 at 05:42 PM |
|
|
Shimming Link Pins
Hey everyone.
Does anyone have a copy of the instructions that come with a new link pin set for shimming the camber correctly?
I have done this before and I'm sure there was paperwork in the box that told me how many inner and outer shims were required depending on the
difference between the trailing arms. The kit that I have just bought has no paperwork.
I'm going to be fitting my Country Buggy spindles to the car tomorrow and need this info ASAP. So if anyone can help out please do!
Thanks
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
toey1984
A.k.a.: nathan kirkman
Commited Dubber
Posts: 73
Threads: 11
Registered: February 26th, 2012
Member Is Offline
Location: telegraph point
Theme: UltimaBB Pro Blue
Mood: skittels
|
| posted on June 21st, 2012 at 05:54 PM |
|
|
http://www.thesamba.com/vw/forum/viewtopic.php?t=350604
or
http://www.historicvws.abelgratis.com/technical/king_pin/king_pins.htm
hope this may help as i know little about link pin
Nathan
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on June 21st, 2012 at 06:57 PM |
|
|
Exactly what I was chasing!
Thank you very much.
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 21st, 2012 at 07:19 PM |
|
|
| Quote: |
come with a new link pin set for shimming the camber correctly?
|
the shims DONT adjust the camber they are for aligning the upper n lower trailing arms so that they move freely and dont bind
Ideally you should check the trailing arms in the VW jig to make sure there straight and also the stub axles for squarenees and alignment of the tie
rod end steering arm
If the above is done correctly then your ride will ride extreamly well
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on June 21st, 2012 at 10:52 PM |
|
|
Ok. Thanks for the info. Nice to learn something new.
I'm sure that the spindles are straight cause they have just been properly rebuilt at a machine shop.
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on June 22nd, 2012 at 11:28 PM |
|
|
| Quote: | Originally
posted by vw54
| Quote: |
come with a new link pin set for shimming the camber correctly?
|
the shims DONT adjust the camber they are for aligning the upper n lower trailing arms so that they move freely and dont bind
Ideally you should check the trailing arms in the VW jig to make sure there straight and also the stub axles for squarenees and alignment of the tie
rod end steering arm
If the above is done correctly then your ride will ride extreamly well
|
Erm, no actually. The shims are there to set the camber to the correct amount VW calculated which is why you have to measure the difference between
the 2 torsion arms to figure out the number of shims required top and bottom plus inner and outer. If the arm difference is less than 5mm or greater
than 9mm then you require new arms as the shimming cannot correct the camber that out of spec arms give 
Don't forget that the arms clamp the link pin in place and so no movement occurs here. All the movement occurs in the LP knuckle and by turning the
LP so that the offset groove rotates the LP in the torsion arm to remove slack from the LP knuckle to torsion arm joint.
You should lightly grease each of the shims so that they movefreely against each other and also reduces wear. Heavy greasing will require readjustment
of the LP's soomer than expected as the bulk of the grease is pressed from them during driving
madness is in the eye of the beholder  |
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 23rd, 2012 at 09:02 AM |
|
|
Errmmm NO, Birch is right Psimitar. The camber is in the design of the stub. Yes you can fuck up the original design by changing the shimming to
change your camber setup, but that will actually be making the link pins wear prematurely as they are actually binding.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on June 23rd, 2012 at 10:22 AM |
|
|
Ermmmmmm, Dave and Matt are right. My race car [No.8 Beetle] has a
little 'fine tuning' on the shims, but that is strictly a track car.
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on June 23rd, 2012 at 11:44 AM |
|
|
I agreed with what has been said above. If you don't fit the right number of inner and outer shims as per the instructions it will cause the stub
axle to kick out at either the top or bottom. Binding up the link pins.
We can't have that cause we want maximum travel and as smooth as possible
Thanks to everyone for their help, I fitted the stubs last night.
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on June 23rd, 2012 at 10:22 PM |
|
|
But that's what I'm saying if you don't shim them properly your camber is not right 
madness is in the eye of the beholder |
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on June 24th, 2012 at 07:22 AM |
|
|
If your camber is not right, it's probably because something is bent.
Check all components [trailing arms, stub-axles etc.], and if nothing is bent, assemble as per above. The camber should be right......there is NO
camber adjustment.
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 24th, 2012 at 07:28 AM |
|
|
yep as said before there is NO camber adjustment on Ling pins
i must take some pics of the VW jigs used for testing arms
|
|
|
