| [ Total Views: 592 | Total Replies: 4 | Thread Id: 100713 ] |
|
|
 Ryno17
Commited Dubber
Posts: 50
Threads: 21
Registered: January 3rd, 2011
Member Is Offline
Location: Coramba NSW
Theme: UltimaBB Pro Blue ( Default )
|
 posted on February 1st, 2013 at 12:04 PM |
|
|
Accurate oil sender position
Hi all just wanted to pick your brains regarding where is the best place to install my oil sender. I have already installed a VDO sender on a T piece
adapter that fits into the standard oil pressure port below the dizzy that also enables a vdo oil pressure sender to be mounted also. The oil sender
works well but the temp sender dose not read properly as there is not enough flow and cant pick up the temp accurately. I have removed it from the
engine and tested it and it works fine. I know the sump plug sender is a good spot but this would last about 10 meters as my car has a deep sump and
is very low. Can you change out the oil relief plug with a sender? I have read this somewhere but I don't want to mess with the pre load tension of
the spring if the sender length is longer than the original plug. I also have herd that you can get dipstick senders? May look a bit ugly but as long
as its accurate.
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on February 1st, 2013 at 12:40 PM |
|
|
hi
You can get the oil pressure relief plug drilled and tapped to accommodate the the sender, this wont upset the pressure springs preload.
There is debate as to what is the best location for the sender, I have always run them in oil pressure relief plug or in the case where the Type 3
filler would normally go and have no failures due to incorrect oil temp data.
Steve
|
|
|
sander288
Custom Title Time!
"Bolt-on Master"
Posts: 1404
Threads: 183
Registered: August 26th, 2008
Member Is Offline
Location: Norman Park, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: This is my bug. There are many others like it, but this one is mine.
|
| posted on February 1st, 2013 at 02:49 PM |
|
|
Mine is where a type 3 filler normally would be; just need to hook up a gauge. This is where Stan tapped it in on my case
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on February 1st, 2013 at 03:59 PM |
|
|
On the deep sump I had on the wench it was in the back of the deep sump, out of the way and worked well, send me your email and I'll send you a
pic.
Don
PS I've still got the sump if your keen, going cheap. 
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on February 3rd, 2013 at 08:29 AM |
|
|
Ryno17, did you get my email
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
