| [ Total Views: 840 | Total Replies: 5 | Thread Id: 101572 ] |
|
|
 pfillery
Insano Dub Head
Posts: 734
Threads: 160
Registered: December 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 11th, 2013 at 10:03 PM |
|
|
Trouble removing bay kombi steering box. Help please!
For the life of me I cannot seem to remove the steering arm from the shaft on the steering box on a bay kombi. The nut is off but the arm will not
budge from the splined shaft. Obviously it has to be off so it will fit through the hole in the chassis. I have used a 3 armed puller and the arms do
not seem to want to grip. Is there a recommended way or something I'm doing wrong? I guess it's been there for 40 years. The tie rod on that arm is
also stuck fast. I don't want to bash it and ruin the thread on the spline.
Do I need to break out the angle grinder and sacrifice the arm??
|
|
|
pod
A.k.a.: paul mrvw061
Compulsive Aussie Vee Dubber
i`ve got to finish this thing one day
Posts: 4980
Threads: 145
Registered: December 28th, 2003
Member Is Offline
Location: campbelltown,nsw
Theme: UltimaBB Pro Yellow
Mood: could be better
|
| posted on April 12th, 2013 at 12:38 AM |
|
|
i used a 2 arm puller on the one i pulled apart ,once i realised it was'nt going to come apart easily, and when it did separate it went with a bang
...lol 
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 12th, 2013 at 09:00 AM |
|
|
I'm doing one today, I hope it'll come off with my Snap-On Pitman arm puller......always a lottery 
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
pfillery
Insano Dub Head
Posts: 734
Threads: 160
Registered: December 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 12th, 2013 at 01:24 PM |
|
|
Might have to Macguyver something in the shed. Have made pullers before using a couple of those hobsons plates with bolts between them to force them
out. Might be the only way. Otherwise sacrifice the arm which is probably easy enough to replace.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 12th, 2013 at 07:23 PM |
|
|
Today's was a TIGHT one, puller maxed out and had to go for oxy heat on the arm. Went off like a gunshot when it popped. Good luck.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
pfillery
Insano Dub Head
Posts: 734
Threads: 160
Registered: December 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 13th, 2013 at 09:03 PM |
|
|
So went to buy a couple of pullers today. Picked up a tie rod end remover which worked a treat on the tie rods. And a pitman arm remover
which.....broke! Good brand too, frame snapped clean in half so not up to the job. Will return it tomorrow for a refund.
But found out (and surprised nobody mentioned it) that you don't need to remove the arm. Only the nut. The arm then fits perfectly through the hole.
Who'd have thunk it?
|
|
|
